E 9133 (31)

Massey Ferguson E 9133 (31) – EEM3 or EEM4: Solenoid valve 3, fast decay error (bank off)

Issue description

The Engine Electronic Control Module (EEM3) has detected a fast decay error related to solenoid valve 3 when the bank is off (often accompanied by FMI 31). This indicates that the fuel injector solenoid valve for cylinder 3 is not closing as quickly as expected during the decay phase of its function after a fuel injection event. This delayed closing can result in an incorrect amount of fuel being injected. As a protective measure, the control system shuts down the entire bank of injectors associated with this fault (typically cylinders 1, 5, and 3 on a six-cylinder engine), resulting in a severe reduction in engine power and limiting engine speed to approximately 1500 RPM.

Applies to these machines

  • 5400 Series
  • 5460
  • 5465
  • 5470
  • 5480
  • 6400 Series
  • 6460
  • 6465
  • 6470
  • 6480
  • 6490
  • 6495
  • 6497
  • 6499
  • 7400 Series
  • 7465
  • 7475
  • 7480
  • 7490
  • 7495
  • 7499
  • 8400 Series
  • 8450
  • 8460
  • 8470
  • 8480
  • 8600 Series
  • 8650
  • 8660
  • 8670
  • 8680
  • 8690
  • 4600 Series
  • 4608
  • 4700 Series
  • 4708
  • 5600 Series
  • 5610

Check the cause

  1. Check the ECU connector locking mechanism to ensure the metallic locking lever is fully seated in its final position

  2. Inspect the wiring harness between the EEM3 ECU and injector solenoid valve 3 for open circuits, short circuits to ground, or shorts between cables

  3. Test the injector solenoid according to the manufacturer's instructions to determine if the coil has failed internally

  4. Evaluate the EEM3 controller itself for defects if the wiring harness is intact and the injector tests fine

Repair steps

  1. Depressurize fuel system

    Turn off the engine and allow the high-pressure fuel system to depressurize.

  2. Locate injector

    Locate injector 3 on the engine.

  3. Repair wiring

    Disconnect the electrical connector to the injector and repair any damaged wiring or terminals found during the diagnostic phase.

  4. Remove fuel line and clamp

    If the injector is deemed faulty, remove the high-pressure fuel line and the injector hold-down clamp.

  5. Remove old injector

    Remove the old injector, ensuring you also remove the old nozzle seating washer and body O-ring.

  6. Install new injector

    Install the new Bosch common rail injector using a new seating washer and O-ring.

  7. Reassemble components

    Reinstall the hold-down clamp, reconnect the high-pressure fuel line, and plug in the electrical connector.

  8. Clear fault codes

    Clear the fault codes using the SisuDiesel EEM3 service tool (WinEEM3s).

Parts you might need

(20)
  • Bosch Common Rail Diesel Fuel Injector

    V837069405
  • Bosch Common Rail Diesel Fuel Injector

    837069405
  • Bosch Common Rail Diesel Fuel Injector

    837069215
  • Bosch Common Rail Diesel Fuel Injector

    0445120340
  • Bosch Common Rail Diesel Fuel Injector

    0445120063
  • Bosch Common Rail Diesel Fuel Injector

    837073791
  • Bosch Common Rail Diesel Fuel Injector

    0445110408
  • Alternate Sisu Injector

    0445120235
  • Bosch Common Rail Injector Nozzle Seating Washer

    F 00R J01 453
  • Bosch Common Rail Injector Body O-ring

    F 00R J01 026
  • Fuel Injector (Solenoid Valve 3)

    V837073713
  • Injector Connector Tube

    V837073785
  • Injector Connector Tube

    F00RJ02717
  • Fuel Injector (AGCO)

    836854791

    Verify correct part number with tractor serial number.

  • Fuel Injector (AGCO)

    V836854791

    Verify correct part number with tractor serial number.

  • Fuel Injector (Bosch Cross-Reference)

    0986435553

    Verify correct part number with tractor serial number.

Get help to fix this fault by requesting a quote

Browse other Massey Ferguson codes