1054

New Holland 1054 – Engine ECU: CAN Message Timeout for ET1

Issue description

The engine control unit (ECU) has not received the 'ET1' CAN bus message within the expected timeframe. The ET1 message is a standard J1939 communication containing critical engine fluid information, specifically engine oil and coolant temperatures. This timeout indicates a breakdown in the data link layer or a loss of communication from the sensors, which can lead to inaccurate dashboard readings, warning lights, and potentially trigger the engine to enter a protective limp mode or derate state.

Applies to these machines

  • T5
  • T6
  • T7
  • L160
  • L170
  • L175
  • L180
  • L185
  • L190
  • L223
  • L225
  • L230
  • C185
  • C190
  • C227
  • C232
  • C238
  • B90B
  • B95
  • B95B
  • B110
  • B110B
  • B115
  • B115B
  • LB75.B
  • LB90.B
  • LB110.B
  • LB115.B
  • W110
  • W130

Check the cause

  1. Check battery voltage and main chassis ground connections, as a weak battery (e.g., 12.1V) can cause ghost communication faults

  2. Visually inspect the CAN bus wiring harness between the engine temperature sensors and the ECU for chafing, abrasion, sharp bends, or corrosion

  3. Disconnect and inspect the connectors for the engine coolant and oil temperature sensors, as well as the main ECU connector, looking for bent or corroded pins, moisture, or a loose fit

  4. Perform CAN bus electrical tests with the key off: measure resistance between CAN High and CAN Low (should be approximately 60 Ohms; 120 Ohms indicates a missing terminating resistor or open circuit, while significantly lower than 60 Ohms indicates a short circuit)

  5. Perform CAN bus electrical tests with the key on: check voltage of CAN lines relative to chassis ground (CAN High should be ~2.5V or slightly above, CAN Low ~2.5V or slightly below; abnormal voltages indicate a short to power or ground)

Repair steps

  1. Address preliminary issues

    Correct any low battery voltage issues and clean/tighten all relevant ground connections. Clear the fault codes and operate the machine to see if the code returns.

  2. Repair CAN bus wiring

    If physical damage to the CAN bus wiring harness is found, insulate minor abrasions, professionally splice compromised sections, or replace the entire harness segment.

  3. Replace faulty temperature sensor

    If wiring and electrical tests are normal, replace the coolant or oil temperature sensor (coolant sensor is the most common failure point). Allow the engine to cool, relieve cooling system pressure, swap the sensor, and top off the coolant.

  4. Final verification

    Clear all fault codes using a diagnostic tool or the vehicle's monitor. Operate the machine and re-check to confirm fault code 1054 does not return.

Parts you might need

(12)
  • OEM New Holland Agriculture. Alternate OEM numbers: 504264463, 82028145, 82025881. Aftermarket cross-references: 47598516, 87307746.

  • Engine Oil Temperature Sensor

    Source based on specific engine model.

  • Example part number. Harnesses are highly specific to machine model and configuration; verify with dealer.

  • Engine Coolant Temperature Sensor (F5C / F5H Engines)

    504264463-CNH

    Depending on exact engine spec/pin count. Located near the thermostat housing. Measures coolant temp to broadcast via the ET1 message.

  • Depending on exact engine spec/pin count. Located near the thermostat housing.

  • Engine Coolant Temperature Sensor

    87688409

    Alternative OEM Part Number for L-Series SSL. Located near the thermostat housing.

  • Example for L220 / C238 / SR175 series. Only replace if the CAN bus wiring and sensors test perfectly but the module fails to broadcast J1939 messages. Requires dealer programming.

  • Engine Coolant Temperature Sensor

    85802504

    Measures coolant temperature and sends information to the ECU

  • Fits New Holland TM series (TM120 to TM190) and Case MXM series. Alternate part: B67043

  • Compatible with New Holland model C175. Alternate parts: 82034415, 87307746

  • Engine Coolant Temperature Sensor

    87341875

    Listed for New Holland T9010 models

  • New Holland OEM part

Get help to fix this fault by requesting a quote

Browse other New Holland codes