New Holland fault codes & repair guides
All 7,052 codes· 50 per page · page 1 of 142
| Code | Controller | Issue summary | Repair manual |
|---|---|---|---|
| 001-03 | — | Hydraulic Charge Pressure Switch Shorted to High Source | Full repair manual for code 001-03 |
| 001-04 | — | Hydraulic Charge Pressure Input Level Low | Full repair manual for code 001-04 |
| 002-03 | — | Hydraulic Reservoir Level Sensor Shorted to High Source | Full repair manual for code 002-03 |
| 003-03 | — | Hydraulic Oil Temperature Switch Shorted to High | Full repair manual for code 003-03 |
| 3 | TMF | Hitch Raise Solenoid High Side Driver Shorted to 12 Volts | Full repair manual for code 3, TMF |
| 4 | TMF | Hitch Raise Solenoid Failed Open or Shorted to Ground | Full repair manual for code 4, TMF |
| 5 | TMF | Hitch Lower Solenoid Shorted to 12 Volts | Full repair manual for code 5, TMF |
| 6 | TMF | Hitch Lower Solenoid High Side Driver Circuit Short to 12 Volts | Full repair manual for code 6, TMF |
| 7 | TMF | Hitch Raise/Lower Solenoids Open or Short to Ground | Full repair manual for code 7, TMF |
| 11 | New Holland Rear Power Take Off | Driver is on and no current is sensed | Full repair manual for code 11, New Holland Rear Power Take Off |
| 11 | TMF | Communications Lost with Data Bus and ALL other controllers | Full repair manual for code 11, TMF |
| 11 | TRANS | Master Clutch Potentiometer Open Circuit or Short to Ground | Full repair manual for code 11, TRANS |
| 12 | TRANS | Master Clutch Potentiometer Short to +12 Volts or Short to 5 Vreff | Full repair manual for code 12, TRANS |
| 14 | TMF | 5 Volt Sensor Supply Voltage Is Too High | Full repair manual for code 14, TMF |
| 15 | TMF | 5 Volt Sensor Supply Voltage Is Too Low | Full repair manual for code 15, TMF |
| 17 | TMF | Hitch Position Command Potentiometer Failure | Full repair manual for code 17, TMF |
| 018 | New Holland Rear Power Take Off | PTO Speed Sensors Wiring Swapped | Full repair manual for code 018, New Holland Rear Power Take Off |
| 18 | TMF | Hitch Rockshaft Position Potentiometer Out of Range | Full repair manual for code 18, TMF |
| 19 | ARM | Hand THROTTLE Potentiometer Failure | Full repair manual for code 19, ARM |
| 19 | TMF | Hitch Upper Limit Potentiometer Failure | Full repair manual for code 19, TMF |
| 21 | TMF | Hitch Load Command Potentiometer Failure in Armrest Controller | Full repair manual for code 21, TMF |
| 23 | TMF | Two Draft Pin Sensors Failed | Full repair manual for code 23, TMF |
| 25 | TMF | Hitch Up/Down Switch Failure in Armrest Controller | Full repair manual for code 25, TMF |
| 26 | TMF | Fender UP and DOWN Switch Failure or Both Switches Simultaneously Pressed | Full repair manual for code 26, TMF |
| 28 | TMF | Hitch Travel Potentiometer Failure in Armrest Controller | Full repair manual for code 28, TMF |
| 29 | ARM | Aux 1st Remote Valve Lever Potentiometer Failed | Full repair manual for code 29, ARM |
| 29 | TMF | Hitch Drop Rate Potentiometer Failed in Armrest Controller | Full repair manual for code 29, TMF |
| 30 | TMF | Right Draft Pin Voltage Out of Range | Full repair manual for code 30, TMF |
| 31 | TMF | Left Draft Pin Voltage Out of Range | Full repair manual for code 31, TMF |
| 33 | TMF | Hitch Slip Set Switch Failed in Armrest Controller | Full repair manual for code 33, TMF |
| 34 | TMF | Hitch Slip Select Switch Failed in Armrest Controller | Full repair manual for code 34, TMF |
| 35 | TMF | Slip Sensor (radar or wheel speed) is failed in the Instrumentation Controller | Full repair manual for code 35, TMF |
| 37 | New Holland Transmission | Clutch Pedal Switch or Clutch Relay Issue | Full repair manual for code 37, New Holland Transmission |
| 37 | TRANS | BOC Switch Open Circuit or Neutral Relay Stuck Open | Full repair manual for code 37, TRANS |
| 38 | TRANS | Shuttled to Reverse Without Wheel Speed Signal | Full repair manual for code 38, TRANS |
| 39 | ARM | Aux 2nd remote valve LEVER potentiometer is failed | Full repair manual for code 39, ARM |
| 41 | TMF | Draft Pin Detected Without Draft Control | Full repair manual for code 41, TMF |
| 42 | TMF | Engine Speed Too Low During Lower Valve Calibration | Full repair manual for code 42, TMF |
| 43 | TMF | No Draft Pin Detected Despite Armrest Controller Specification | Full repair manual for code 43, TMF |
| 44 | TMF | Hitch Calibration Aborted Due to Tractor Movement | Full repair manual for code 44, TMF |
| 45 | TMF | Hitch Calibration Attempted When Engine Is Not Running | Full repair manual for code 45, TMF |
| 47 | TMF | Raise Valve Calibration Value Is Too High | Full repair manual for code 47, TMF |
| 47 | TRANS | Clutch Pedal Switch Misadjusted | Full repair manual for code 47, TRANS |
| 48 | TMF | Raise Valve Calibration Value Is Too Low | Full repair manual for code 48, TMF |
| 49 | ARM | Aux 3rd Remote Valve Lever Potentiometer Failed | Full repair manual for code 49, ARM |
| 49 | TRANS | Auto Guidance Isolation Valve Driver Fault | Full repair manual for code 49, TRANS |
| 50 | TMF | Hitch Position at Top of Travel Not Within Specification During Calibration | Full repair manual for code 50, TMF |
| 50 | TRANS | Park Brake Is Powered Off When in Park | Full repair manual for code 50, TRANS |
| 51 | TMF | Lower Valve Calibration Value is Too High | Full repair manual for code 51, TMF |
| 51 | TRANS | Park Position Not Recognized | Full repair manual for code 51, TRANS |
