24

New Holland 24 – TMF: Communications Lost with Instrumentation Controller

Issue description

The Tractor Multi-Function (TMF) controller has lost its CAN bus data link with the instrument cluster (Instrumentation Controller Unit). This interruption prevents the exchange of critical operational data, such as engine speed, ground speed, and sensor statuses, which affects the ability to monitor or control certain functions related to the instrumentation system. The underlying condition is typically a failure in the CAN bus network caused by an open circuit, short circuit, or electrical noise.

Applies to these machines

  • TM120
  • TM130
  • TM140
  • TM155
  • TM175
  • TM190
  • TG210
  • TG230
  • TG255
  • TG285
  • T8 Series
  • Magnum 235
  • Magnum 340
  • WORKMASTER 70
  • T4.75

Check the cause

  1. Check for other active or stored fault codes (multiple communication codes may indicate a general network problem rather than a single failed module)

  2. Verify battery and charging system health, as low voltage can cause modules to drop off the network and generate ghost codes

  3. Inspect all fuses related to the instrument cluster and control modules, ensuring the cluster receives switched power, constant power, and a solid ground

  4. Visually inspect the CAN bus wiring harness (twisted yellow and green wires) for chafing, pinching, corrosion, or connector damage

  5. Perform a CAN bus termination resistor check with power off (measure resistance between CAN High and CAN Low; should be approximately 60 ohms. A reading of 120 ohms indicates a missing resistor or open circuit; significantly lower than 60 ohms suggests a short circuit or faulty module)

  6. Perform a CAN bus voltage check with key on/engine off (CAN High should be 2.5-3.0V, CAN Low should be 2.0-2.5V to a clean ground. Deviations can indicate a short or a faulty module pulling the voltage up or down)

Repair steps

  1. Isolate faulty component

    Disconnect modules one by one, starting with the instrument cluster. If disconnecting it does not resolve the issue, reconnect it and proceed to disconnect other modules on the network (e.g., armrest controller, transmission controller) one at a time. The module that restores communication to the rest of the network when disconnected is likely the culprit.

  2. Repair wiring and connectors

    If wiring issues were found during inspection, repair the damaged section of the CAN harness and ensure all connections are clean, tight, and corrosion-free.

  3. Replace faulty module

    Replace the identified faulty module (e.g., instrument cluster). Note that new instrument clusters often require programming with machine-specific software using the New Holland Electronic Service Tool (EST).

  4. Clear codes and calibrate

    Use a diagnostic tool to clear all fault codes. Recalibrate systems such as the transmission or hitch if their respective controllers were replaced.

Parts you might need

(10)
  • Instrument Cluster

    51580158

    For WORKMASTER 70 (after March 20, 2023)

  • Instrument Cluster

    51451233

    For WORKMASTER 70 (before March 19, 2023)

  • For T4.75 (NAR Market), replaces 84289366

  • Instrument Cluster

    47522651

    Requires software programming upon installation; verify model fitment

  • Replaces 87617964. 5-connector module. Specific part numbers depend on the tractor's transmission speed and serial number breaks.

  • TMF Module (Tractor Multifunction Controller)

    51563038

    Replaces 87364402.

  • TMF Module (Tractor Multifunction Controller)

    87364402

    Replaced by 51563038.

  • TMF Module (Tractor Multifunction Controller)

    87524908C

    Core return option.

  • TMF Module (Tractor Multifunction Controller)

    87393065

    5-connector module.

Get help to fix this fault by requesting a quote

Browse other New Holland codes