1207

New Holland 1207 – UCM: Invalid Configuration Between IC and UCM

Issue description

There is a mismatch in the configuration data or memory parameters stored between the Instrument Cluster (IC) and the Universal Control Module (UCM). The system recognizes that the programmed settings or software versions in these two modules do not align, which typically happens if one module was replaced, updated, or suffered a memory corruption (EEPROM error) without being properly synced to the other.

Applies to these machines

  • SR220
  • SR250
  • SV250
  • SV300
  • L213
  • L215
  • L216
  • L218
  • L220
  • L221
  • L223
  • L225
  • L230
  • C227
  • C232
  • C238
  • TR320
  • TV380
  • T Series
  • TS Series
  • TLA Series
  • TSA Series

Check the cause

  1. Verify fault code 1207 is active using the machine's onboard diagnostics or instrument cluster menu

  2. Check for other active fault codes, particularly code 9403, which is related to configuration issues

  3. Check the battery and power supply to ensure it is fully charged with clean, tight connections, as low or unstable voltage can cause communication errors

  4. Visually inspect the wiring harnesses and connectors between the Instrument Cluster and the UCM for damage, corrosion, or loose connections (clean connectors with a water displacement product like WD-40 if the machine was recently pressure washed)

Repair steps

  1. Connect Electronic Service Tool (EST)

    Connect a laptop with the CNH EST software to the machine's diagnostic port using a DPA5 or similar protocol adapter.

  2. Establish communication

    Turn the machine's ignition on and establish a connection with the vehicle's control modules through the EST software.

  3. Backup existing configuration

    Before making any changes, back up the existing configuration from the UCM and IC.

  4. Reconfigure the machine model

    Intentionally configure the machine to an incorrect model, and then re-configure it back to the correct model. This forces a rewrite of the configuration files on the modules.

  5. Clear fault codes

    After the reconfiguration is complete, use the EST to clear all fault codes.

  6. Verify the repair

    Cycle the ignition off and on, and then check for any returning fault codes to ensure the issue is resolved. If the fault returns, proceed to hardware replacement.

Parts you might need

(18)
  • Universal Control Module (UCM) / ECU

    84529539

    Also listed as 47395504. Fits various skid steers (C227, C232, C238, L213-L230). Requires programming.

  • Fits various New Holland BigBaler and Roll-Belt models. Requires programming.

  • Instrument Cluster (IC)

    91789483

    Replaces 84384716, 84239242. Fits various skid steer and compact track loaders. Reman version: 91789483R.

  • Instrument Cluster (IC)

    84413348

    Fits New Holland skid steer loaders C227, C232, C238, L213, L216, L218, L220, L221, L223, L225, L230.

  • Instrument Cluster (IC)

    48152873

    Blank instrument cluster for various skid steer models, requires overlay buttons to be installed.

  • Instrument Cluster (IC)

    84142612

    Fits T/TS/TLA/TSA Series Tractors. Repair services are available for these clusters.

  • Instrument Cluster (IC)

    87346616

    Fits T/TS/TLA/TSA Series Tractors. Repair services are available for these clusters.

  • Instrument Cluster (IC)

    87517297

    Fits T/TS/TLA/TSA Series Tractors. Repair services are available for these clusters.

  • Instrument Cluster (IC)

    87745383

    Fits T/TS/TLA/TSA Series Tractors. Repair services are available for these clusters.

  • Instrument Cluster (IC)

    47132006

    Fits T/TS/TLA/TSA Series Tractors. Repair services are available for these clusters.

  • Instrument Cluster (IC)

    84413346

    Fits New Holland Skid Steers and CTLs (L213-L230, C227-C238). Note that part numbers supersede frequently based on the machine's build date (NRC vs. Tier 4).

  • Instrument Cluster (IC)

    84384716

    Fits New Holland Skid Steers and CTLs (L213-L230, C227-C238). Note that part numbers supersede frequently based on the machine's build date (NRC vs. Tier 4).

  • Instrument Cluster (IC) - Remanufactured

    84239243R

    Fits New Holland Skid Steers and CTLs (L213-L230, C227-C238). Note that part numbers supersede frequently based on the machine's build date (NRC vs. Tier 4).

  • Instrument Cluster (IC) - Remanufactured

    91789483R

    Fits New Holland Skid Steers and CTLs (L213-L230, C227-C238). Note that part numbers supersede frequently based on the machine's build date (NRC vs. Tier 4).

  • Instrument Cluster (IC) - Remanufactured

    91789482R

    Fits New Holland Skid Steers and CTLs (L213-L230, C227-C238). Note that part numbers supersede frequently based on the machine's build date (NRC vs. Tier 4).

  • Universal Control Module (UCM)

    48084571

    Highly specific to the exact engine tier and machine options. Must be programmed via New Holland EST with the correct software version to match the machine's specific PIN upon installation.

  • Universal Control Module (UCM)

    47845627

    Highly specific to the exact engine tier and machine options. Must be programmed via New Holland EST with the correct software version to match the machine's specific PIN upon installation.

  • Universal Control Module (UCM)

    47775233

    Highly specific to the exact engine tier and machine options. Must be programmed via New Holland EST with the correct software version to match the machine's specific PIN upon installation.

Get help to fix this fault by requesting a quote

Browse other New Holland codes