126

New Holland 126 – MIU, MCC1, Vehicle 2 Controller, EGR Controller, Instrument Cluster: Battery Voltage Fault

Issue description

The system has detected a general issue related to the battery voltage, which may affect the proper operation of the machine's electrical system. The voltage supplied to an electronic control unit has fallen outside of its expected operating range, indicating a voltage that is too high, too low, or unstable.

Applies to these machines

  • T-Series
  • T7
  • TM Series
  • 40 Series
  • T6000
  • TD Series
  • TSA Series
  • CR Series
  • CX Series
  • CR920
  • CR940
  • CR9040
  • CR9060
  • CR9070
  • CR9080
  • CX840
  • FR Series
  • FX Series
  • Loaders
  • Backhoes
  • Compact Track Loaders
  • Loader Backhoes

Check the cause

  1. Check battery condition using a digital multimeter (static voltage should be 12.6V or higher) and perform a load test (CCA should be at least 75% of rating)

  2. Inspect battery terminals, main power, and ground connections at the starter and chassis for tightness and corrosion

  3. Test the alternator output with the engine running; voltage across battery terminals should be stable between 13.8 and 14.4 volts. A fluctuating reading points to a failing voltage regulator, and output above 14.8 volts indicates an overcharging condition

  4. Visually inspect and check the tightness of main ground straps, particularly the braided strap connecting the engine to the machine's frame

Repair steps

  1. Confirm the fault

    Clear the fault code and operate the machine to see if the code reappears. If it returns, proceed with diagnosis.

  2. Isolate the cause - Battery

    If the battery failed the load test (CCA below 75% of rating), it will need to be replaced.

  3. Isolate the cause - Alternator

    If the alternator output is low, fluctuating, or non-existent, check the alternator's main power connection and the smaller exciter wire plug for corrosion or damage. If connections are good, the alternator is likely faulty and requires replacement.

  4. Isolate the cause - Wiring and grounds

    If the battery and alternator test well, inspect the main wiring harnesses for chafing, corrosion, or rodent damage, paying close attention to major connector blocks. Check for loose connections at the starter and main power distribution points. Inspect and tighten all major ground connections, especially from the battery to the frame and the engine/cab to the frame.

  5. Repair and Replace

    Replace the battery, alternator, or damaged wiring as identified in the previous steps. When replacing components, ensure all new connections are clean and tight.

  6. Verify the repair

    Once parts have been replaced, start the machine and re-check the charging voltage. Ensure no warning lights or fault codes return.

Parts you might need

(9)
  • Heavy-Duty Battery

    BNHD5W

    SmartStart Premium Heavy-Duty. A generic '665 Type' 12V 120AH battery is also listed for many 40, T6000, TD, and TSA series tractors.

  • Heavy-Duty Battery

    ENG8D

    Used in various tractors including T7 and TM series.

  • Alternator87592254

    12V, 185 Amp. Manufacturer: Leece Neville / Motorola. Fits many CR and CX series combines and FR/FX forage harvesters.

  • Replaced by 504338098R.

  • Alternator (Remanufactured)

    504338098R

    Replaces 87715398R.

  • Ground Strap

    D140369

    Listed for various Compact Track Loaders and older Loader Backhoes.

  • Ground Strap

    FAE14301B

    11 inches long.

  • Ground Strap

    D1NN14301H

    7 inches long.

  • Listed for T7.250 tractors.

Get help to fix this fault by requesting a quote

Browse other New Holland codes