New Holland 14001 – TCU: Rear PTO Sensor Shorted to +12V
Issue description
The transmission control unit (TCU) has detected a short circuit to the +12V power supply, or an open circuit, in the rear PTO speed sensor circuit. This indicates that the sensor's signal wire is likely making unintended contact with a 12-volt power source or the circuit is broken, preventing the control module from receiving a valid signal. This condition causes improper operation of the sensor and affects the functionality of associated systems, including dashboard tachometer readings, automated engine load adjustments, and safety diagnostics for the electronic PTO clutch.
Applies to these machines
50 machines- T4.55
- T4.65
- T4.75
- T4.85
- T4.90
- T4.95
- T4.100
- T4.105
- T4.110
- T4.115
- T4.120
- T5 Series
- T6.120
- T6.140
- T6.150
- T6.155
- T6.160
- T6.165
- T6.175
- T6.180
- T7.165
- T7.170
- T7.175
- T7.185
- T7.190
- T7.200
- T7.210
- T7.220
- T7.225
- T7.230
- T7.235
- T7.245
- T7.250
- T7.260
- T7.270
- T6010
- T6020
- T6030
- T6050
- T6070
- T6080
- T6090
- TM115
- TM125
- TM135
- TM150
- TM165
- Workmaster 55
- Workmaster 65
- Workmaster 75
Check the cause
Verify battery voltage is stable and within the correct range, as low voltage can trigger erroneous fault codes.
Visually inspect the wiring harness leading to the rear PTO speed sensor for chafing, melting, or corrosion, especially near moving parts or hot surfaces.
Disconnect the electrical connector for the rear PTO speed sensor and inspect the pins for corrosion, moisture intrusion, or damage.
Check for the presence of fault code 14002 (short to ground). If 14002 is absent, it confirms the issue is likely a short to power or an open circuit.
Repair steps
Locate the sensor
Find the rear PTO speed sensor, which is typically mounted on the rear transmission housing, positioned over the internal PTO drive gear.
Test the wiring harness
Disconnect the harness from the sensor and the control module. Using a multimeter set to continuity mode, check for a short between the signal wire and the power supply wire. Check for continuity on the ground wire to the chassis. Finally, inspect for an open circuit by checking for continuity from end to end on each wire in the sensor's circuit.
Test the sensor
If the wiring harness checks out, test the inductive sensor for internal shorts. If an internal short is found, the sensor is the point of failure.
Replace the sensor
Replace the faulty sensor. When installing the new sensor, ensure the air gap between the sensor and the tone wheel is set correctly, if it is adjustable.
Clear Fault Codes
After the repair is complete, use a diagnostic tool to clear the fault code from the control module's memory.
Verify the Repair
Start the tractor and engage the PTO at various speeds to ensure the system is functioning correctly and the fault code does not reappear.
Parts you might need
(8)- Rear PTO Speed Sensor47767004
- Rear PTO Speed Sensor84165809
Interchangeable with 47767004
Rear PTO Speed Sensor
82022718Interchangeable with 47767004
Rear PTO Speed Sensor
82030541Interchangeable with 47767004
- Rear PTO Speed Sensor87564763
- Rear PTO Speed Sensor82036589
Superseded by 87564763
- Rear PTO Speed Sensor47767014
- Rear PTO Speed Sensor84390014
Interchangeable with 47767014
Get help to fix this fault by requesting a quote