New Holland 14002 – ICU: Transmission Oil Filter Switch Closed to Ground on Power Up
Issue description
The transmission oil filter pressure switch is electrically shorted to ground at the moment the machine is powered on. The control unit detects that the switch's electrical circuit is already completed to ground when it shouldn't be. This condition signifies an immediate electrical problem, such as a short in the wiring or a failed sensor, rather than an actual clogged filter, and can potentially affect the transmission system's performance.
Applies to these machines
56 machines- T5
- T6
- T7
- T4020V
- T4030F
- T4030V
- T4040
- T4050
- T4050F
- T4050V
- T4060F
- T5040
- T5050
- T5060
- T5070
- T6010
- T6020
- T6030
- T6040
- T6050
- T6060
- T6070
- T6080
- T6090
- T7030
- T7040
- T7050
- T7060
- TM115
- TM120
- TM125
- TM130
- TM135
- TM140
- TM150
- TM155
- TM165
- TM175
- TM190
- TN55
- TN60
- TN65
- TN70
- TN75
- TN80
- TN85
- TN90
- TN95
- TS100A
- TS115A
- TS125A
- TS135A
- 8160
- 8260
- 8360
- 8560
Check the cause
Visually inspect the wiring harness leading to the transmission oil filter pressure switch for chafing, cuts, or heat damage from exhaust components.
Check the electrical connector at the switch for corrosion, loose pins, or moisture ingress.
Inspect and replace the transmission oil filter if its service interval has been exceeded or if its condition is unknown, as a severely clogged filter can potentially cause a pressure differential.
Disconnect the switch and test for continuity with the engine off. A normally open switch should show no continuity; if it shows closed to ground, the switch is internally shorted.
With the switch disconnected and ignition on (do not start the engine), use a multimeter to check the signal wire in the harness connector for a short to ground. If detected, the wiring is the issue.
Check all related fuses in the fuse box for any that may be loose or blown.
Repair steps
Safety First
Park the tractor on a level surface, engage the parking brake, and turn off the engine. Disconnect the negative battery cable to prevent any electrical shorts during the repair.
Locate the Switch
The transmission oil filter pressure switch is typically located on or near the transmission filter housing. Its exact position can vary by tractor model.
Prepare for Oil Spillage
Place a suitable container and rags under the switch to catch any transmission fluid that may leak out when the switch is removed.
Remove the Old Switch
Disconnect the electrical connector from the switch. Using an appropriately sized wrench, carefully unscrew and remove the old pressure switch.
Install the New Switch
Ensure the threads on the new switch and the port on the filter housing are clean. If the new switch does not have pre-applied thread sealant, apply a small amount to the threads. Screw the new switch into place and tighten it to the manufacturer's specified torque. Do not overtighten, as this can damage the switch or the housing.
Final Connections
Reconnect the electrical connector to the new switch, ensuring it is secure. Reconnect the negative battery cable.
Test the Repair
Start the engine and check for any leaks around the newly installed switch. Clear the fault codes using a diagnostic tool or through the instrument cluster's procedure, if available. Operate the tractor to ensure the fault code does not reappear and that the transmission operates smoothly. Check the transmission fluid level and top off as needed.
Parts you might need
(17)Common OEM part number. Verify fitment by serial number.
Supersedes part number 87395493.
Transmission Oil Filter Pressure Switch
87395493May be superseded by 51581233.
Transmission Oil Filter Pressure Switch
82030730Verify fitment by serial number.
Verify fitment by serial number.
Transmission Oil Filter Pressure Switch
79043250Verify fitment by serial number.
Verify fitment by serial number.
Verify fitment by serial number.
Listed as SENSOR; Oil Filter for T6.145 model.
Adapter Kit
May be required for some aftermarket replacement switches if replacing an older style switch (e.g., part number 82028154).
Common for T6000, T7000, T7.xxx series, and TM series. Ensure you match the thread pitch (e.g., M14x1.5) and connector type.
Common for older series like the 40 series, TS, etc. Ensure you match the thread pitch and connector type.
Transmission Oil Pressure Switch / Filter Switch
F0NN7E440ABLegacy Ford/New Holland part number. Ensure you match the thread pitch and connector type.
Transmission Oil Pressure Switch / Filter Switch
F0NN7E440BALegacy Ford/New Holland part number. Ensure you match the thread pitch and connector type.
Transmission Filter
1346028C1Case IH part for Axle and Transmission/High Flow. Verify fitment with dealer.
- Hydraulic Oil Filter84240234
New Holland part for some T8 models. Verify fitment with dealer.
Replaces F0NNU909AB, 81872035. Common hydraulic/transmission restriction switch. Confirm correct part number with a dealer using the tractor's serial number.
Get help to fix this fault by requesting a quote