14011

New Holland 14011 – ICU: Engine Speed Sensor Circuit Issue

Issue description

The engine speed sensor is experiencing a short to positive (VCC) or an open circuit. This condition disrupts the proper functioning of the sensor, which is critical for monitoring engine revolutions per minute (RPM). As a result, the instrument cluster does not receive a valid engine speed signal, which can affect various tractor functions.

Applies to these machines

  • TM120
  • TM140
  • TM155
  • TM175
  • TM190
  • T6010
  • T6020
  • T6030
  • T6040
  • T6050
  • T6060
  • T6070
  • T6080
  • T6090
  • T7030
  • T7040
  • T7050
  • T7060
  • T7070
  • TS100A
  • TS110A
  • TS115A
  • TS125A
  • TS130A
  • TS135A
  • T4.75F

Check the cause

  1. Visually inspect the wiring harness leading to the engine speed sensor for any signs of damage, such as fraying, corrosion, or breaks. Check the sensor itself for visible damage.

  2. Disconnect and inspect the electrical connector for the sensor. Look for corrosion, bent pins, or a loose connection.

  3. Using a multimeter, perform a power and ground test. With the ignition on, back-probe the connector to check for specified voltage (typically 5V or 12V) and verify ground wire resistance to the chassis is less than 5 Ohms.

  4. For magnetic sensors, disconnect the sensor and measure resistance across its terminals. An open circuit (infinite resistance) or out-of-spec reading indicates a faulty sensor.

  5. Perform a signal output test while cranking the engine. For Hall effect sensors, back-probe the signal wire for DC voltage pulses. For magnetic sensors, check for a small AC voltage.

  6. Inspect the tone ring (often located on the flywheel) for damage, debris, metal shavings, or missing teeth, which can cause an erratic signal.

Repair steps

  1. Disconnect battery

    Disconnect the battery before beginning any work on the electrical system to ensure safety.

  2. Locate the sensor

    Locate the engine speed sensor. It is typically found on the engine's bell housing reading the flywheel, or on the front of the transmission (consult the specific machine's service manual for exact placement).

  3. Remove the old sensor

    Disconnect the electrical connector. Remove the bolt(s) securing the sensor to the housing and carefully pull the sensor out. Note: Access may be tight and could require the removal of other components, such as a hydraulic filter.

  4. Install the new sensor

    Install a new O-ring on the new sensor and lubricate it with clean engine oil. Insert the new sensor into its mounting hole and tighten the retaining bolt to the manufacturer's specified torque.

  5. Reconnect and test

    Reconnect the electrical connector, ensuring it clicks into place. Reconnect the battery, start the engine, and check if the fault code has cleared and the tachometer is functioning correctly. Perform a test drive to ensure all related functions are restored.

Parts you might need

(11)
  • Also referred to as a crankshaft position sensor. Used by the engine control unit to adjust fuel injection and ignition timing.

  • Direct replacement for select Case IH and Ford/New Holland tractors (including T4, T5, T6, and T7 series). Replaces part numbers 2853552 and 87803075.

  • For T4, T5, T6 Series

  • Engine Speed Sensor

    4897243

    For T4, T5, T6 Series

  • Engine Speed Sensor

    504155506

    For T4, T5, T6 Series

  • Engine Speed Sensor

    504189766

    For T4, T5, T6 Series

  • Engine Speed Sensor

    504359090

    For T4, T5, T6 Series

  • Engine Speed Sensor

    47522763

    For T4, T5, T6 Series

  • For T9 Series & Case IH Steiger (Replaces older part)

  • For Older/Other NH Models

  • For Older/Other NH Models

Get help to fix this fault by requesting a quote

Browse other New Holland codes