14022

New Holland 14022 – Instrument Cluster: Cranking Line Shorted to Ground

Issue description

The instrument cluster has detected an electrical short to ground in the circuit responsible for sensing the engine cranking signal. This circuit communicates to the tractor's electronic systems that the operator has turned the key to the 'start' position. A short to ground in this line can interrupt the normal starting sequence, potentially preventing the engine from cranking or causing unexpected behavior during the starting process.

Applies to these machines

  • T4
  • T5
  • T7
  • T7.170
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • TM115
  • TM120
  • TM125
  • TM130
  • TM135
  • TM140
  • TM150
  • TM155
  • TM165
  • TM175
  • TM190
  • TD60D
  • TD95D
  • TC Series
  • Boomer Series

Check the cause

  1. Advise the operator to pause briefly after turning the key to the 'ON' position to allow the electronic modules to initialize before attempting to crank the engine, as turning the key too quickly can generate an intermittent 14022 code.

  2. Load-test the battery and ensure all battery terminals and chassis ground connections are clean, tight, and free of corrosion.

  3. Visually inspect the wiring harness between the ignition switch, the instrument cluster, and the starter relay for signs of chafing, melting, or rodent damage.

  4. Disconnect and inspect the primary instrument cluster connector (C079) for corrosion or backed-out pins, paying special attention to pin 16 on applicable models.

Repair steps

  1. Isolate the starter relay

    Locate the starter relay, often labeled K2 in the tractor's wiring diagrams.

  2. Test the starter signal wire

    Using a test light or multimeter, check for voltage at the small signal wire on the starter solenoid while an assistant turns the key to the 'crank' position. If voltage is present but the engine doesn't crank, the starter motor or solenoid is likely faulty. If no voltage is present, the fault lies upstream in the cranking circuit (ignition switch, starter relay, or wiring); proceed to the next step.

  3. Test the starter relay circuit

    Check for power and ground at the starter relay's coil terminals when the key is turned, and check for battery voltage at the main input terminal. If power is supplied to the coil but the relay does not click or send power to the starter, replace the relay.

  4. Inspect the cranking line wire

    Disconnect the instrument cluster connector C079 and the starter relay. Use a multimeter to check for continuity to ground on the cranking signal input wire (pin 16 on some models). If continuity to ground is found, locate and repair or replace the shorted section of the wiring harness.

Parts you might need

(10)
  • Starter Relay

    Component ID often K2 in schematics. Must be sourced based on specific tractor model.

  • Instrument Cluster Wiring Harness

    84057109

    Example part number for some models. Verify fitment by serial number.

  • Ignition Switch

    86569718

    Example part number for TC25D. Verify fitment by serial number.

  • Instrument Cluster

    Model-specific. Replace only if the cluster itself is proven faulty.

  • Ignition Switch

    82826806

    Fits Workmaster 45, 50, 55, 60, 65, 70, 75 and TT series tractors.

  • Ignition Switch

    87304791

    Fits Workmaster 45, 50, 55, 60, 65, 70, 75 and TT series tractors.

  • Replaces 83989947. 70 Amp, 12V, 4-pin relay.

  • Replaced by 82012872. Compatible with T6 and T7 series models. 70 Amp, 12V, 4-pin relay.

  • 70 Amp, 12V, 4-pin relay.

  • General application, verify fitment with parts catalog.

Get help to fix this fault by requesting a quote

Browse other New Holland codes