1521

New Holland 1521 – UCM or MIU: Left Brake Lights Open Circuit

Issue description

The controlling module has detected a break in the electrical circuit that operates the left-hand brake light. An open circuit prevents current from flowing, resulting in the left brake light failing to illuminate when the brake pedal is pressed. This can be a safety issue and may affect the vehicle's compliance with lighting regulations. The system identifies this fault when it does not detect the expected electrical load from the brake light bulb.

Applies to these machines

  • T6
  • T7
  • T8
  • T1510
  • T1520
  • T2210
  • T2310
  • TC30
  • TC35A
  • TC40A
  • TC45A
  • Boomer 3050
  • TM115
  • TM120
  • TM125
  • TM130
  • TM135
  • TM140
  • TM150
  • TL70
  • TL80
  • TL90
  • TL100
  • TS90
  • TS100
  • TS115
  • 1215
  • 1220
  • 1320
  • 1520
  • 1620
  • 1920
  • 2120
  • 5640
  • 6640
  • 7740
  • 8160
  • 8260
  • L200
  • C200

Check the cause

  1. Check the left brake light bulb for a broken filament (burnt-out bulb), which is the most common cause of an open circuit.

  2. Visually inspect the left tail light assembly for physical damage or moisture ingress.

  3. Inspect the wiring harness leading to the light for any signs of damage, corrosion, or loose connections.

  4. Check the brake light circuit fuse in the fuse box for continuity.

  5. Inspect the 7-pin trailer socket for damage or debris that could be causing a short circuit affecting the tractor's lighting circuits.

Repair steps

  1. Confirm the fault

    Start the tractor and press the brake pedal. Have an assistant confirm that the left brake light is not illuminating.

  2. Test for power at the light connector

    Disconnect the wiring harness from the left tail light assembly. Set a multimeter to DC voltage, connect the black probe to a known good chassis ground, and probe the harness contacts with the red probe while an assistant presses the brake pedal. If approximately 12 volts is present, the issue is likely the tail light assembly or the bulb socket. If there is no voltage, the issue is further up the circuit.

  3. Test the brake light switch

    Locate the brake light switch at the top of the brake pedal assembly. Disconnect its electrical connector and use a multimeter set to continuity (Ohms). With the pedal released, there should be no continuity. When pressed, the switch should close and show continuity (close to zero ohms). Alternatively, test for voltage: one terminal should have constant power, and the other should become live when the pedal is pressed. Replace the switch if it fails either test.

  4. Inspect and repair the wiring harness

    If the brake light switch functions correctly but there is still no power at the tail light connector, visually trace the wiring harness from the switch to the rear of the tractor. Look for pinched, frayed, or broken wires, paying close attention to connectors and junctions. Repair any found breaks using a weatherproof butt connector and heat shrink tubing.

Parts you might need

(26)
  • Brake Light Bulb

    CLC1011582

    Standard 12V automotive bulb (21W or 23W). For Rustler models.

  • Brake Light Bulb

    529068

    Standard 12V automotive bulb (21W or 23W). Replaces MT40007207, 12V 21W.

  • Left Tail Light Assembly

    51446421

    Fits T8 series.

  • Fits various T6 and T7 series.

  • Fits JX and TT series.

  • For L200 & C200 skid steers.

  • For TL series.

  • Brake Light SwitchSBA385200731

    Fits many TC, T, and Boomer models.

  • Brake Light SwitchSBA385200730

    Fits many TC, T, and Boomer models.

  • Brake Light Switch

    83968919

    Fits many TC, T, and Boomer models.

  • Brake Light Switch

    4954118

    Fits various JX, MXU, TL, TM, TN, TS models.

  • Brake Light Switch

    A57725A

    Fits various JX, MXU, TL, TM, TN, TS models.

  • Red Tail/Stop Light Assembly (12V, 27W)

    87627854

    Manufactured for CNH Industrial; fits the left or right rear of New Holland 200-series and Case loaders

  • Generic fitment for New Holland head/tail light sockets; verify exact wattage requirements on your specific housing before installation.

  • Replacement Halogen Bulb (12V, 50W/55W)

    139119A1

    Generic fitment for New Holland head/tail light sockets; verify exact wattage requirements on your specific housing before installation.

  • OEM complete assembly for models like T4030. LH and RH units are different parts.

  • OEM complete assembly for models like T4050.

  • OEM complete assembly for T6000/T6/T7000/T7 Series.

  • 12V, 21/5W, for combined tail and brake light functions.

  • Bulb #894, 37.5W, 12V

  • Halogen Bulb

    84292121

    20W Halogen Bulb for work lamp, also fits tail light on some models

  • Actia OEM part

  • Utility Control Module (UCM)

    51678591

    For Skid Steer and Wheel Loaders

  • Utility Control Module (UCM)

    84529539

    Fits various C and L series skid steers

  • Fits various C and L series skid steers

  • Wiring Harness

    87738587

    Example rear light bar harness for European L175; verify specific part number by machine configuration

Get help to fix this fault by requesting a quote

Browse other New Holland codes