New Holland 19817 – DCU: DEF Dosing Valve Stuck Closed
Issue description
The engine's control module has determined that the Urea Dosing Valve (UDV) is not operating as expected and is likely stuck in the closed position. This prevents the correct amount of Diesel Exhaust Fluid (DEF) from being injected into the exhaust stream. The control module identifies this implausible signal because the valve's state does not match the expected value for the current operating conditions. This malfunction can lead to increased NOx emissions, illumination of the SCR or engine warning light, and potentially a countdown to engine torque limitation or a complete inability to start the engine.
Applies to these machines
19 machines- T7.170
- T7.220
- T7.235
- T7.250
- T7.260
- T7.270
- Puma Series
- T4 Series
- T5 Series
- TK4 Crawler Series
- 5130 Combine
- 6130 Combine
- 7130 Combine
- 7230 Combine
- 8230 Combine
- 9230 Combine
- Backhoe loaders
- Compact track loaders
- Crawler dozers
Check the cause
Visually inspect the entire SCR system for white crystalline residue (indicating a DEF leak), and check the dosing valve, lines, and connectors for damage, corrosion, or heat-related wear
Check DEF quality and level to ensure the tank is filled with non-contaminated fluid meeting the ISO 22241 standard
Inspect the wiring harness and connectors between the Dosing Control Unit (DCU) and the dosing valve for opens, shorts, or corrosion
Perform a resistance test on the dosing valve's coil using a multimeter (expected resistance is typically 11 to 18 ohms)
Monitor DEF line pressure using a diagnostic tool to rule out a supply pump issue, blocked filter, or frozen line
Perform a Urea Dosing System Test (UDST) or Small Quantity Test using a diagnostic scan tool to observe the spray pattern and measure the dispensed DEF quantity (expected 5.2g to 6.8g)
Repair steps
Prepare machine
Park the machine on a level surface, turn off the engine, remove the ignition key, and allow the exhaust system to cool completely.
Locate and access dosing valve
Locate the dosing valve (or injector) mounted on the exhaust pipe, typically as part of the DPF/SCR assembly.
Disconnect lines and connectors
Carefully unlock and disconnect the electrical connector from the dosing valve and inspect for corrosion. Disconnect the DEF supply line(s) by pressing the lock on the connector and pulling the line off, having a container ready to catch residual DEF spills.
Remove dosing valve
Remove the two or three mounting bolts holding the valve in place. Gently remove the valve, heat shield, and gasket from the exhaust pipe housing.
Clean mounting surface
Thoroughly clean the mounting surface on the exhaust pipe, removing any carbon buildup or old gasket material to ensure a proper seal.
Install new valve
Install the new heat shield, gasket, and dosing valve. Tighten the mounting bolts to the manufacturer's specified torque, then securely reconnect the DEF lines and electrical connector.
Verify repair
Use a diagnostic tool to clear fault codes and perform a dosing system test to prime the system. Start the engine, check for leaks, and perform a parked regeneration if required.
Parts you might need
(7)Also replaces 84247021, LB02P01011P1, and 84247021R (remanufactured). Often a Bosch component.
Alternative part numbers include 91897169, 47581676, 47662288, 47750812, 87677584. Replacement may require software installation and programming.
Bosch part number 0444025027.
Urea Dosing Valve / DEF Dosing Module
0444023058Bosch OEM part number
New Holland / Case IH OEM part number
- Urea Dosing Valve / DEF Dosing Module5801730656
New Holland / Case IH OEM part number
Urea Dosing Valve / DEF Dosing Module
504374327New Holland / Case IH OEM part number
Get help to fix this fault by requesting a quote