2076

New Holland 2076 – TCM: Flywheel Speed Sensor Open Circuit

Issue description

The Transmission Control Module (TCM) is not receiving a signal from the flywheel speed sensor. The system has detected an open circuit, indicating a break or disconnection in the electrical circuit associated with the sensor. This prevents proper transmission of the engine speed signal, which can lead to issues with automatic gear shifting and inaccurate RPM readings on the dashboard.

Applies to these machines

  • T6.120
  • T6.140
  • T6.145
  • T6.155
  • T6.160
  • T6.165
  • T6.175
  • T6.180
  • T7.165
  • T7.170
  • T7.175
  • T7.185
  • T7.190
  • T7.210
  • T7.220
  • T7.225
  • T7.230
  • T7.235
  • T7.245
  • T7.250
  • T7.260
  • T7.270
  • T6010
  • T6020
  • T6030
  • T6040
  • T6050
  • T6060
  • T6070
  • T6080
  • T6090
  • T7030
  • T7040
  • T7050
  • T7060
  • TM115
  • TM120
  • TM125
  • TM130
  • TM135
  • TM140
  • TM150
  • TM155
  • TM165
  • TM175
  • TM190
  • TS100A
  • TS110A
  • TS115A
  • TS125A
  • TS130A
  • TS135A
  • TS90
  • TS100
  • TS110
  • TS115
  • TL70
  • TL80
  • TL90
  • TL100
  • Ford 40 series
  • Ford 60 series

Check the cause

  1. Visually inspect the flywheel speed sensor (located on the flywheel housing at the rear of the engine) and its wiring harness for cuts, abrasions, melting, or burning.

  2. Check the sensor's electrical connector for bent, corroded, or pushed-back pins. Ensure the connector is clean and securely latched.

  3. Check for continuity on the ground wire between the sensor connector and a known good chassis ground. Resistance should be very low (under 5 Ohms).

  4. For 3-wire Hall effect sensors, check for battery voltage at the power pin of the connector.

  5. For 2-wire inductive sensors, measure resistance across the two pins (typically 800-2500 Ohms). A reading of infinity (OL) indicates a broken internal coil.

  6. For 2-wire inductive sensors, back-probe the signal wire with a multimeter set to AC voltage. While cranking the engine, verify a small AC voltage that increases with engine speed.

  7. For 3-wire Hall effect sensors, back-probe the signal wire with a multimeter set to DC volts. While cranking, verify the voltage pulses between a low and high state (e.g., 0V to 5V).

Repair steps

  1. Prepare machine for service

    Ensure the tractor is on a level surface, the parking brake is engaged, and the engine is off. Disconnect the battery to prevent electrical shorts.

  2. Access the sensor

    Locate the flywheel speed sensor on the engine's flywheel housing. Remove any obstructing components or panels to gain access.

  3. Remove the faulty sensor

    Disconnect the electrical connector. Remove the mounting bolt(s) securing the sensor. Gently twist or pry the sensor out. If seized, carefully apply heat to the surrounding housing.

  4. Install the new sensor

    Clean the mounting surface on the housing. Ensure the new O-ring or seal is properly seated. Insert the new sensor, secure with mounting bolt(s) to OEM torque specs, and firmly reconnect the electrical connector.

  5. Test and calibrate

    Reconnect the battery, start the tractor, and verify that fault code 2076 has cleared. Perform any necessary calibration procedures as indicated by the service manual.

Parts you might need

(10)
  • Replaces 87680718. Fits T6, T7, T6000, T7000, TS-A, TM series and Case IH Puma, Maxxum, MXU series.

  • Flywheel Speed Sensor (2-Pin Inductive)

    85802950

    Replaces 83996843, F0NN11N008AA, F0NN11N008AB. Fits TS, TS-A, TM, TL, T6000, Ford 40/60 series, and Case IH MXM.

  • Speed Sensor87564761

    Monitors component speed for New Holland Agriculture.

  • Speed Sensor47767004

    Replaces 84165809. Fits T7.170 and T7.210.

  • Speed Sensor47766973

    Replaces 84169162. Fits T7.170.

  • Depending on the specific tractor model and engine configuration

  • Flywheel Speed Sensor

    452446A3

    Depending on the specific tractor model and engine configuration

  • OEM part.

  • OEM part. Replaces 82028157.

  • OEM part.

Get help to fix this fault by requesting a quote

Browse other New Holland codes