New Holland 2099 – TCM: Open Circuit of the Clutch Electromagnet 5
Issue description
The fault code indicates an open circuit in the clutch electromagnet 5, also known as the Clutch C5 (17th Gear) Solenoid in 16x16 transmissions. This means the electrical signal from the Transmission Control Module (TCM) is not reaching the solenoid, preventing it from functioning correctly. The root cause is typically a broken wire, a loose electrical connection, or a failure within the solenoid's internal coil.
Applies to these machines
33 machines- 8160
- 8260
- 8360
- 8560
- TM115
- TM120
- TM125
- TM130
- TM135
- TM140
- TM150
- TM155
- TM165
- TM175
- TM190
- TS90
- TS100
- TS110
- TS115
- TS100A
- TS110A
- TS115A
- TS125A
- TS135A
- TL70
- TL80
- TL90
- TL100
- TL70A
- TL80A
- TL90A
- TL100A
- T7030
Check the cause
Visually inspect the wiring harness leading to the transmission and the C5 clutch solenoid for frayed wires, corrosion, or loose connectors. Ensure all connections are clean and securely seated.
Check for voltage at the connector of the C5 solenoid using a multimeter with the tractor keyed on. A lack of voltage indicates a wiring or TCM issue.
Perform a resistance test by disconnecting the solenoid and measuring across its terminals with a multimeter. A healthy solenoid should read between 5 and 30 ohms. Infinite resistance indicates an internal open circuit and a failed solenoid.
Perform a 'click' test by briefly applying 12-volt power to the solenoid's terminals. If no audible click is heard, the solenoid is likely seized or burnt out.
Repair steps
Safety First
Park the tractor on a level surface, engage the parking brake, and disconnect the battery.
Locate the Solenoid
The transmission solenoids are typically located on the valve body inside the transmission housing. On some models, this may require splitting the tractor to access the transmission.
Drain Transmission Fluid
Place a drain pan under the transmission and drain the hydraulic fluid.
Access the Valve Body
Depending on the tractor model, you may need to remove a transmission pan or other components to access the valve body where the solenoids are mounted.
Identify and Remove the C5 Solenoid
Carefully disconnect the wiring harness from the faulty solenoid. The solenoids may be held in place by bolts or a locking plate. Remove the fasteners and carefully extract the solenoid from the valve body.
Install the New Solenoid
Compare the new solenoid with the old one to ensure it is the correct part. Install the new solenoid into the valve body, secure it with the original fasteners, and reconnect the wiring harness.
Reassembly
Reinstall any components that were removed to access the valve body, such as the transmission pan (using a new gasket).
Refill and Test
Refill the transmission with the correct type and amount of hydraulic fluid. Reconnect the battery, start the tractor, and check for any leaks. Clear any fault codes and operate the transmission to ensure the repair was successful.
Parts you might need
(4)- Transmission Solenoid5164627
OEM part. Cross-references: 5144771, 5139049, 47125301, 84488341. Fits TL, TM, TS, M, and 60 Series with Powershift, Dual Command, and Range Command transmissions.
- Transmission Solenoid5168052
OEM part for TM and 60 Series tractors.
- Transmission Solenoid9970157
OEM part for TM and 60 Series tractors.
Transmission Solenoid Valve
QTP-41657Aftermarket part for Ford New Holland 60 and TM series, and Fiat M series.
Get help to fix this fault by requesting a quote