2346

New Holland 2346 – TCU: Clutch 5-6 Solenoid Circuit Fault

Issue description

The Transmission Control Module (TCM) has detected an electrical fault in the circuit for the 5-6 clutch electromagnet (solenoid). This indicates either an open circuit, a short to ground, or a short to the chassis in the wiring harness or the solenoid itself. This fault prevents the pulse-width modulated (PWM) solenoid from properly controlling the hydraulic oil flow required to engage the 5th and 6th gears.

Applies to these machines

  • T8.275
  • T8.300
  • T8.330
  • T8.360
  • T8.380
  • T8.390
  • T8.410
  • T8.420
  • T8.435

Check the cause

  1. Visually inspect the wiring harness leading to the transmission and the clutch 5-6 solenoid for chafing, breaks, or corrosion.

  2. Disconnect the solenoid's electrical connector and check for moisture, dirt, or bent pins that could interrupt the signal.

  3. Perform a resistance test across the disconnected solenoid terminals; infinite resistance indicates an open circuit within the coil.

  4. Check for correct voltage supply from the TCU and verify continuity to chassis ground at the solenoid connector with the key on.

Repair steps

  1. Safety First

    Ensure the tractor is on a level surface, the parking brake is engaged, and the engine is off. Disconnect the battery before working on the electrical system.

  2. Locate the Component

    Locate the clutch solenoids on the exterior of the transmission housing. Refer to the tractor's service manual for the exact location of the clutch 5-6 solenoid.

  3. Perform Diagnostic Checks

    Carry out the visual and electrical checks described in the diagnostic section to confirm the point of failure.

  4. Wiring Repair

    If the fault is in the wiring harness, repair or replace the damaged section. Ensure all connections are clean and secure.

  5. Solenoid Replacement

    If the solenoid is faulty, disconnect the electrical connector, clean the area, unscrew and remove the solenoid (expecting some hydraulic fluid to leak). Install the new solenoid with correctly fitted and lubricated O-rings/seals, torque to the manufacturer's specified value, and reconnect the connector.

  6. Clear Fault Codes

    Reconnect the battery, start the tractor, and use the diagnostic menu or a service tool to clear the stored fault codes.

  7. Test Operation

    Operate the tractor and shift through all the gears to ensure the repair has been successful and the fault code does not reappear. A clutch calibration procedure may be required after replacing a transmission component.

Parts you might need

(15)
  • Transmission Clutch Solenoid Valve

    87640495

    Manufacturer: CNH Industrial. Listed for T8 series (T8.275 through T8.435). Confirm correct part number with a dealer using the tractor's serial number.

  • May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • Solenoid Valve

    51426026

    May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • Solenoid Valve

    87456901

    May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • Solenoid Valve

    190432A1

    May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • Solenoid Valve

    86508388

    May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • May not be the exact correct replacement for the Clutch 5-6 solenoid. Always confirm with a parts diagram or dealer.

  • Potential part number for T8 series; verify fitment with serial number

  • Potential part number for T8 series; verify fitment with serial number

  • Transmission Control Valve Assembly

    450728A2

    Assembly may include solenoids; verify fitment with serial number

  • Transmission Control Valve Assembly

    450729A2

    Assembly may include solenoids; verify fitment with serial number

  • Transmission Control Valve Assembly

    87323842

    Assembly may include solenoids; verify fitment with serial number

  • Transmission Control Valve Assembly

    450724A2

    Assembly may include solenoids; verify fitment with serial number

Get help to fix this fault by requesting a quote

Browse other New Holland codes