2365

New Holland 2365 – TCM: C1-2 Clutch Not Calibrated

Issue description

The transmission control module (TCM) has detected that the fill time and pressure settings for the C1-2 clutch pack have not been learned or are no longer valid. This is a software-level fault that affects the operation of the tractor's transmission system, requiring a calibration procedure to ensure smooth gear engagement. It commonly occurs after a new transmission controller is installed, the controller's memory has been reset, or after certain mechanical repairs to the transmission.

Applies to these machines

  • T8.320
  • T8.350
  • T8.380
  • T8.410
  • Magnum 235-340
  • T7.210
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • T7030
  • T6 Series
  • T9 Series

Check the cause

  1. Ensure transmission oil temperature is within the required range (typically 10°C to 60°C, or >60°C depending on the specific model)

  2. Verify engine speed can be maintained at approximately 1200 RPM (+/- 100 RPM)

  3. Ensure the parking brake is engaged

  4. Ensure the operator is seated, activating the seat switch

  5. Verify shuttle and gear levers are in the correct starting position (often Neutral or Forward)

  6. Verify there are no other active transmission or engine fault codes (e.g., sensor, potentiometer, or solenoid faults like 2344 must be resolved before calibration)

  7. Check that battery voltage is stable and sufficient

Repair steps

  1. Warm up tractor

    Operate the tractor to bring the transmission oil temperature to the required range. This can be checked via the tractor's diagnostic menu (e.g., H-menu).

  2. Position tractor

    Park the tractor on level ground, engage the parking brake, and ensure all implements are lowered and safe.

  3. Enter calibration mode

    With the engine off, enter calibration mode. Methods vary by model: Method A (e.g., T7 Power Command) - Key on, shuttle in Neutral, hold upshift/downshift buttons, start engine, release buttons. Method B (e.g., Electro Command) - Hold upshift/downshift buttons, start engine, release. Method C - Access the 'H' diagnostic menu and select the calibration routine (e.g., H1).

  4. Initiate calibration

    When the dashboard displays 'CAL', 'CL', or the oil temperature, set the engine speed to approximately 1200 RPM. Follow on-screen prompts, which may involve placing the shuttle lever in Forward.

  5. Calibrate clutches

    Start the automatic calibration sequence or manually select the C1-2 clutch using the upshift/downshift buttons. For C1 and C2 clutches, the procedure might involve depressing the clutch pedal, placing the range lever in neutral, setting RPM, releasing the pedal, and then using the upshift/downshift buttons to calibrate each clutch. The engine RPM will momentarily dip as the clutch engages and the controller records the required hydraulic pressure.

  6. Store calibration values

    Once the sequence finishes and the display shows 'END' or 'EE', turn the engine off. Wait at least 10-15 seconds to allow the controller to store the new calibration values in its memory.

  7. Verify operation

    Start the tractor and operate the transmission to ensure shifts are smooth and the 2365 fault code does not reappear.

Parts you might need

(13)
  • Transmission Clutch Solenoid

    Only required if calibration repeatedly fails due to a faulty C1-2 solenoid (typically accompanied by code 2344).

  • Transmission Temperature Sensor

    Only required if a faulty sensor prevents the calibration from starting.

  • Transmission Speed Sensor

    Only required if a faulty sensor interrupts the calibration process.

  • Fits various TL, TM, TS, and M series tractors. Verify fitment by serial number.

  • Listed as a solenoid for New Holland equipment. Verify fitment by serial number.

  • Fits certain Iveco engines used in New Holland and Case IH models like the Maxxum and MXM series. Verify fitment by serial number.

  • C1-2 Clutch Solenoid Valve

    QTP-409730

    Aftermarket PMV solenoid for C1/C2 clutch packs in Ford New Holland 40 and TS series, as well as some Case IH models.

  • For Powershift transmission on New Holland T8.330. Verify by serial number.

  • PWM valve assembly

    450728A2

    Includes individual solenoids. Verify by serial number.

  • Verify exact fitment with the machine's serial number via the CNH parts catalog.

  • Transmission Clutch Solenoid Valve / Proportional Solenoid

    84286798

    Verify exact fitment with the machine's serial number via the CNH parts catalog.

  • Verify exact fitment with the machine's serial number via the CNH parts catalog.

  • Verify exact fitment with the machine's serial number via the CNH parts catalog.

Get help to fix this fault by requesting a quote

Browse other New Holland codes