New Holland 2368 – TCU: Low Range Clutch Not Calibrated
Issue description
The low range clutch within the transmission has not been properly calibrated. The Transmission Control Unit (TCU) has not learned the necessary pressure and timing required to engage the low range clutch pack smoothly, which negatively affects transmission performance in low range. This fault is also triggered when a new, uncalibrated controller is installed.
Applies to these machines
22 machines- T7 Series
- T8 Series
- TM Series
- TM115
- TM120
- TM125
- TM130
- TM135
- TM140
- TM150
- TM155
- TM165
- TM175
- TM190
- 60 Series
- 8160
- 8260
- 8360
- 8560
- Genesis 70 Series
- G170
- 8670
Check the cause
Check for other active fault codes (e.g., clutch pedal potentiometer, speed sensors, solenoid open/short circuits) and resolve them first, as they will prevent calibration
Ensure transmission oil temperature is between 10°C and 60°C (50°F and 140°F). Warm up the tractor if 'CL' is displayed, or let it cool if 'CH' is displayed
Verify the tractor is parked on level ground with the park brake engaged
Ensure the operator is seated in the seat to satisfy the operator presence switch
Check that all hydraulic levers and the shuttle lever are in the neutral position
Repair steps
T7 Series Calibration - Enter Calibration Mode
Ensure the tractor is on level ground and the park brake is on. With the engine off, press and hold both the upshift and downshift buttons. Start the engine, then release the buttons. The display should show the transmission oil temperature or 'CAL'.
T7 Series Calibration - Perform Calibration
Set the engine speed to approximately 1200 RPM. Depress the clutch pedal, move the shuttle lever to the forward position, and then release the clutch pedal. Press the auto-shift button for an automatic calibration. The display will show the clutches being calibrated in sequence (e.g., A, B, C) and will display 'END' or 'CF' when complete. Turn the engine off and wait for at least 10 seconds to allow the controller to store the new calibration values.
T8 Series Calibration - Enter Calibration Mode
With the tractor running, access the diagnostic menu by pressing and holding the 'PROG' button while turning the key on. Navigate to the 'TCU' (Transmission Control Unit) menu and find the transmission setup or calibration option (often 'ETC').
T8 Series Calibration - Perform Calibration
Follow the on-screen prompts, which will include setting the engine RPM (around 1100 RPM), and engaging the shuttle lever to forward after pressing the clutch. The system will then calibrate the clutches. When finished, the display will indicate completion. Turn the tractor off to save the values.
Genesis / 60 Series Calibration - Enter Calibration Mode
With the engine off, move the shift lever to the neutral downshift position and hold it to the left while turning the key on and starting the engine. On some models, you may need to release the lever as soon as the dash lights up. 'CC' on the display indicates calibration mode.
Genesis / 60 Series Calibration - Perform Calibration
Set the engine RPM to 1200 RPM. Push the shifting lever forward to make 'CC' flash. The tractor will then calibrate the clutches. After completion, stop the engine and wait 10 seconds before restarting.
Parts you might need
(14)- Low Range Clutch Solenoid5164627
Common transmission solenoid. Cross-references include 5144771, 5139049, 47125301, 84488341. Verify exact part by serial number.
Alternate solenoid part number. Verify fitment with dealer.
Transmission Solenoid (Alternate)
51426026Alternate solenoid part number. Verify fitment with dealer.
Alternate solenoid part number. Verify fitment with dealer.
Alternate solenoid part number. Verify fitment with dealer.
Wiring Harness
Inspect for damage if calibration repeatedly fails.
Internal Transmission Components
In rare cases, a mechanical issue within the clutch pack itself could be the cause of repeated calibration failures.
Low Range Clutch Pack
44500Manufactured by CARLISLE. Fits T6000, T7, T7000, and TM series.
- Low Range Clutch Pack5199903
Manufactured by CARLISLE. Fits T6000, T7, T7000, and TM series.
Regulates the hydraulic pressure to the clutch pack.
Regulates the hydraulic pressure to the clutch pack.
- Master Clutch Solenoid51523989
Fits many T7, T8, Puma, and Magnum series tractors.
Used in various transmission and PTO control valves.
Get help to fix this fault by requesting a quote