3011

New Holland 3011 – ENGINE: Air Intake Temperature Sensor Low Voltage

Issue description

The Engine Control Module (ECM) has detected a voltage signal from the Air Intake Temperature (AIT) sensor that is below the normal operating range, indicating an abnormal condition in the temperature reading of the incoming air. This typically suggests a short circuit to ground, a faulty sensor, or an issue with the wiring harness. Because the ECM uses this input to adjust the air-fuel mixture for optimal combustion, an incorrect low-temperature reading can lead to excessive fuel injection, resulting in poor fuel economy, rough idling, and hard starting.

Applies to these machines

  • T7.170
  • T7.185
  • T8.xxx
  • TG210
  • TG230
  • TG255
  • TG285
  • TL80A
  • TL90A
  • TL100A
  • JX-U Series
  • L216
  • L218
  • L220
  • L221
  • L223
  • L225
  • L228
  • L230
  • L234
  • C227
  • C232
  • C238
  • B95B
  • B95C
  • B110B
  • B110C
  • B115B
  • W50C
  • W60C
  • W70C
  • W80C

Check the cause

  1. Visually inspect the wiring harness and connector leading to the Air Intake Temperature Sensor for signs of damage, chafing, corrosion, or loose pins

  2. Disconnect the sensor's electrical connector and inspect the pins for cleanliness and proper fit. Clean the connector and the mating pins on the sensor

  3. Perform a sensor resistance test using a multimeter and compare readings to manufacturer temperature specifications (e.g., approx. 10,000 Ohms at 25°C)

  4. Check the signal wire in the harness connector for a short to ground (a reading of 0 volts with ignition on and sensor disconnected)

  5. Check the signal wire for a short to power (ensure no voltage is present on the signal wire when disconnected)

Repair steps

  1. Confirm the fault

    Clear the fault codes and run the machine to see if code 3011 returns. If it does, proceed with further diagnostics.

  2. Test and replace sensor

    Measure the resistance between the sensor pins. If the measured resistance is significantly lower than the values specified for the current ambient temperature, or if it indicates a dead short, replace the sensor.

  3. Inspect and repair wiring

    If the sensor tests within the correct resistance range, thoroughly inspect and test the wiring harness for continuity and shorts between the sensor connector and the ECM connector. Repair any damaged sections of the harness.

  4. Test Engine Control Module (ECM)

    In rare cases, if both the sensor and the wiring are confirmed to be in good condition, the fault may lie within the ECM. Test the system with a known good test ECU; if the fault does not become active, the original ECU may need replacement.

Parts you might need

(16)
  • Verify part number before ordering. Aftermarket suppliers list this as the intake temp sensor, but official CNH catalogs list it as a Water in Fuel (WIF) sensor. Visually identify the faulty sensor on the engine's air intake system and verify the part number directly from the old component or through an official dealer.

  • OEM part compatible with New Holland TSA Series and Case IH Maxxum/MXM series

  • OEM combined pressure and temperature sensor

  • OEM New Holland / Case IH

  • OEM New Holland / Case IH

  • OEM New Holland / Case IH

  • Air Intake Temperature Sensor

    026123001A

    Bosch compatible sensor, cross-references to OEM 504307953

  • Air Temperature Sensor Probe

    87775490

    Fits various Case IH and New Holland models.

  • Fits various Case IH and New Holland models.

  • Air Temperature Sensor Probe

    323015A1

    Fits various Case IH and New Holland models.

  • Compatible with New Holland T6000 and T7000 series tractors, as well as some Case IH Maxxum and Puma models.

  • Manufactured by Bosch, Bosch Part # 026123001A.

  • Fits various New Holland combine harvesters and sprayers.

  • OEM CNH Part

  • Air Intake Temperature Sensor

    0281006304

    Bosch (OEM Supplier)

  • Air Intake Temperature Sensor

    180998

    Febi Bilstein (Aftermarket)

Get help to fix this fault by requesting a quote

Browse other New Holland codes