3060

New Holland 3060 – ECU: Injector Solenoid Valve Cylinder 1 Not Plausible

Issue description

The Engine Control Unit (ECU) has detected an unclassifiable error or implausible signal from the fuel injector solenoid valve on cylinder 1. This indicates that the solenoid's operation or feedback is inconsistent or outside expected operational parameters. The root cause may be an electrical fault in the solenoid's coil or wiring, or a mechanical issue within the injector that affects its electronic operation. This malfunction disrupts fuel delivery to cylinder 1, typically resulting in engine misfires, rough running, excessive smoke, and a noticeable loss of power.

Applies to these machines

  • T6.120
  • T6.140
  • T6.150
  • T6.155
  • T6.160
  • T6.165
  • T6.175
  • T6.180
  • T7.165
  • T7.170
  • T7.175
  • T7.185
  • T7.190
  • T7.200
  • T7.210
  • T7.220
  • T7.225
  • T7.230
  • T7.245
  • T7.250
  • T7.260
  • T7.270
  • TS100A
  • TS110A
  • TS115A
  • TS125A
  • TS135A
  • T6020
  • T6030
  • T6050
  • T6070
  • T6080
  • T6090
  • B100B
  • B100BLR
  • B100BTC
  • B110 Tier 3
  • B110B
  • B110BTC
  • B115 Tier 3
  • B115B
  • B95B
  • B95BLR
  • B95BTC
  • D85B
  • D95B
  • SR250
  • SV250
  • SV300
  • TR320 Tier 4A
  • TV380 Tier 4A

Check the cause

  1. Inspect Wiring and Connectors: Carefully examine the wiring harness leading to the cylinder 1 fuel injector. Look for any signs of damage, such as chafing, breaks, or melted insulation. Disconnect the electrical connector at the injector and inspect for corrosion, bent pins, or a loose connection.

  2. Check Solenoid Resistance: With the injector connector disconnected, use a multimeter set to a low resistance range (Ohms) to measure the resistance across the two terminals of the injector solenoid. For many Bosch common rail injectors used in these engines, the resistance should be very low, typically in the range of 0.2 to 0.8 ohms. A reading that is significantly higher (open circuit) or lower (short circuit) indicates a faulty solenoid coil.

  3. Perform an Insulation Test (Advanced): For intermittent issues, a standard resistance test may not be sufficient. An insulation tester (megohmmeter) can be used to check for degraded winding insulation. With the injector disconnected, check the resistance between each terminal and the injector body. The reading should be very high (greater than 10 Megaohms).

  4. Listen for Solenoid Actuation: In some cases, you can listen for the 'click' of the injector solenoid when the engine is cranking or running to determine if it is being actuated. A diagnostic tool can also perform an injector 'buzz test' to cycle the solenoid.

  5. Monitor Engine Performance: Note any symptoms like rough idle, excessive smoke (particularly blue or gray), hard starting, or a noticeable loss of power, as these are common indicators of a failing injector.

Repair steps

  1. Safety First

    Ensure the engine is off and has cooled down. Relieve any pressure from the common rail fuel system according to the manufacturer's guidelines. Disconnect the negative battery terminal.

  2. Access the Injector

    Depending on the machine, this may involve removing engine covers, intake manifolds, or other components to gain access to the fuel rail and the cylinder 1 injector.

  3. Clean the Area

    Thoroughly clean the area around the injector and the high-pressure fuel line connection to prevent any dirt or debris from entering the fuel system or the cylinder head.

  4. Disconnect Fuel Lines

    Carefully disconnect the high-pressure fuel line from the top of the injector. It is critical to use a backup wrench to avoid damaging the line or fittings. Also, disconnect the fuel return line. Note that high-pressure fuel lines are often single-use and should be replaced after being removed.

  5. Remove the Injector

    Unbolt the injector hold-down clamp and carefully remove the injector from the cylinder head. This may require a gentle twisting motion or a specialized puller if it is seized.

  6. Install the New Injector

    Ensure the injector bore in the cylinder head is clean. Install the new injector with a new sealing washer and torque the hold-down clamp to the manufacturer's specifications.

  7. Reconnect Fuel Lines

    Install a new high-pressure fuel line and reconnect the return line, torquing all fittings to the specified values.

  8. Final Assembly and Bleeding

    Reassemble all components that were removed. Reconnect the battery. Bleed the fuel system according to the manufacturer's procedure to remove any air that was introduced.

  9. Clear Fault Codes and Test

    Start the engine, clear the fault code using a diagnostic tool, and check for any fuel leaks. Allow the engine to run and verify that the performance issues are resolved and the fault code does not return. Some systems may require an injector coding or calibration procedure to be performed with a diagnostic tool.

Parts you might need

(10)
  • Common Rail Fuel Injector (Bosch)

    0445120073

    Cross-reference: 504128307, 504194432. Widely used in T6 and T7 series tractors.

  • Common Rail Fuel Injector (Bosch)

    0445120054

    Cross-reference: 2855491, 504091504, 2995474. Used in backhoe loaders and dozers with Iveco 445 engines.

  • Common Rail Fuel Injector (Bosch)

    0445110457

    Cross-reference: 5801470098, 504091504, 5801376566. Used in F5/F34 series 3.2L and 3.4L engines.

  • New Holland OEM part. Check with dealer for specific applications.

  • New Holland OEM part. Listed for various T-series tractors.

  • Always order replacement injectors based on the Engine Serial Number (ESN). May need to input trim code into Engine ECU.

  • Ford/New Holland Fuel Injector

    500307714R

    Always order replacement injectors based on the Engine Serial Number (ESN). May need to input trim code into Engine ECU.

  • Remanufactured Fuel Injector / Nozzle (Case IH / New Holland)

    735255C91

    Always order replacement injectors based on the Engine Serial Number (ESN). May need to input trim code into Engine ECU.

  • Core - Fuel Injector

    1934199C1

    Always order replacement injectors based on the Engine Serial Number (ESN). May need to input trim code into Engine ECU.

  • Fuel Injector

    E6NN9F593AA

    Fits older models like 7610, 7710, TW25, 8830. Always order replacement injectors based on the Engine Serial Number (ESN). May need to input trim code into Engine ECU.

Get help to fix this fault by requesting a quote

Browse other New Holland codes