3065

New Holland 3065 – ECU: Injector Solenoid Valve Cylinder 5 - SOURCE HIGH

Issue description

The Engine Control Unit (ECU) has detected an abnormally high voltage or a short circuit to a power source in the electrical circuit of the fuel injector solenoid for cylinder number five. This indicates an electrical fault in the circuit or component, which will likely cause the engine to experience a misfire, rough running, and excessive smoke.

Applies to these machines

  • T-series
  • TL70
  • TL80
  • TL90
  • TL100
  • W50C
  • W60C
  • W70C
  • W80C
  • W130D
  • W190C
  • W230C
  • W270C
  • B95B
  • B100B
  • B110B
  • B115B
  • L221
  • L223
  • L228
  • L321
  • L328
  • C227
  • C232
  • C237
  • C327
  • D85B
  • D95B

Check the cause

  1. Visually inspect the wiring harness leading to the cylinder 5 fuel injector for chafing, melting, or breaks in the insulation.

  2. Disconnect the electrical connector at the injector and examine terminals on both the harness and injector sides for corrosion, bent pins, or a loose fit.

  3. Check for a short to power: With the injector disconnected and ignition ON (engine off), measure voltage between each pin on the harness-side connector and chassis ground. If both wires show battery voltage, there is a short circuit.

  4. Perform an injector solenoid resistance test: Measure resistance across the two terminals of the disconnected injector. Compare to other injectors (should be within 10%). An 'OL' (infinite) or near-zero reading indicates a failed injector.

  5. Perform an insulation test using a megohmmeter. A reading below 10 MΩ between a terminal and the injector body indicates insulation breakdown.

  6. Swap the cylinder 5 injector with an injector from another cylinder. If the fault code follows the injector to the new cylinder, the injector is faulty. If it remains on cylinder 5, the issue is in the wiring or ECU.

Repair steps

  1. Repair wiring or connectors

    If diagnostic checks reveal a damaged wire or connector, repair or replace the faulty section of the harness. Clean any dirty connectors with a suitable contact cleaner and ensure all connections are secure.

  2. Replace fuel injector

    If the injector solenoid is confirmed faulty (open, shorted, or out of spec), replace the injector. Ensure the area around the injector is meticulously clean to prevent fuel system contamination. Use a calibrated torque wrench to tighten the injector to manufacturer specifications to avoid distorting the body.

  3. Recode or calibrate injector

    On common rail systems, use diagnostic software to code or calibrate the new injector to the ECU, ensuring precise control.

Parts you might need

(14)
  • Fuel Injector504063465

    OEM FPT / Iveco part

  • Fuel Injector5801569141

    For Tier 4 engines

  • OEM FPT / Iveco part

  • Fuel Injector

    2855491

    OEM FPT / Iveco part

  • Fuel Injector

    504091504

    OEM FPT / Iveco part

  • Fuel Injector

    0445120054

    Bosch part number

  • Fuel Injector

    99474913

    OEM FPT / Iveco part

  • Fuel Injector

    0432291655

    Bosch part number

  • Fuel Injector / Injector Solenoid Valve

    504117273

    Always verify the exact part number against your machine's specific Engine Serial Number (ESN). Do not mix aftermarket and genuine injectors.

  • Always verify the exact part number against your machine's specific Engine Serial Number (ESN). Do not mix aftermarket and genuine injectors.

  • Always verify the exact part number against your machine's specific Engine Serial Number (ESN). Do not mix aftermarket and genuine injectors.

  • Always verify the exact part number against your machine's specific Engine Serial Number (ESN). Do not mix aftermarket and genuine injectors.

  • Fuel Injector / Injector Solenoid Valve

    0445120075

    Bosch OEM Manufacturer part. Always verify the exact part number against your machine's specific Engine Serial Number (ESN). Do not mix aftermarket and genuine injectors.

  • Fuel Injector / Injector Solenoid Valve

    0986435530

    Bosch OEM Manufacturer part. Always verify the exact part number against your machine's specific Engine Serial Number (ESN). Do not mix aftermarket and genuine injectors.

Get help to fix this fault by requesting a quote

Browse other New Holland codes