3071

New Holland 3071 – ECU: Injector Solenoid Valve Cylinder 3 - No Signal

Issue description

The Engine Control Unit (ECU) has detected a loss of signal from the electronic solenoid valve for the fuel injector on cylinder 3. This prevents the ECU from communicating with or controlling the injector, halting proper fuel injection for that cylinder. This condition typically leads to engine misfires, rough running, excessive smoke, and reduced power.

Applies to these machines

  • T4
  • T5
  • T6
  • T7
  • T7.170
  • T7.200
  • Powerstar
  • Workmaster
  • Boomer
  • B-series
  • C-series
  • L-series
  • SR-series
  • SV-series
  • CR
  • T9

Check the cause

  1. Inspect the main injector wiring harness and the 14-pin pass-through connector at the valve cover for damage, corrosion, moisture, or bent/loose pins.

  2. Check for continuity in the injector harness wiring between the ECU connector and the cylinder 3 injector connector to rule out open circuits or high resistance.

  3. Measure resistance between the cylinder 3 injector signal wire and the engine block ground to check for a short circuit.

  4. Disconnect the harness from the injector and measure the resistance across the two terminals of the injector solenoid, comparing it to manufacturer specifications.

  5. Perform a 'wiggle test' on the injector wiring harness with the engine running to identify intermittent connections or breaks.

Repair steps

  1. Prepare machine

    Park on a level surface, turn off the engine, engage the parking brake, disconnect the battery, and ensure the engine has cooled down.

  2. Access injectors

    Remove the engine valve cover and any other components obstructing access to the fuel injectors and the injector wiring harness.

  3. Repair or replace harness

    If diagnostic checks revealed a wiring fault (short to ground or open circuit), repair the specific wire or replace the injector harness section. Ensure all connections are clean and secure.

  4. Replace fuel injector

    If the injector solenoid is faulty, disconnect the fuel line and electrical connector. Remove the hold-down bolt and extract the injector. Install the new injector with a new copper sealing washer and lubricated rubber O-ring. Torque hold-down bolts to spec (e.g., 9 Nm + 75-degree turn), fuel inlet tube to 50 Nm, and electrical harness nuts to 1.5 Nm.

  5. Final assembly and test

    Reinstall the valve cover with a new gasket. Reconnect the battery, start the engine, clear fault codes with a diagnostic tool, and check for leaks or returning codes.

Parts you might need

(11)
  • Fuel Injector504128307

    Fits some T6 and T7 series tractors (alternate: 504194432)

  • Fits various tractors including T6020 and T7 series

  • Fuel Injector5801906153

    Fits FPT Cursor 13 engines, CR and T9 series combines (alternate: 5801906153R)

  • Fuel Injector5801790338

    Fits Iveco F5 engines, loaders and tractors (alternate: 5801792504)

  • Fuel Injector

    0445120075

    Bosch part for some T7 models

  • Fuel Injector

    504385978

    Fits FPT F5C engines in skid steers and track loaders

  • Fuel Injector500307714

    New Holland injector

  • Injector Wiring Harness

    Replace section if wiring fault is found

  • Valve Cover Gasket

    Replace when reinstalling valve cover

  • Copper Sealing Washer

    Ensure in place before installing new injector

  • Rubber O-ring

    Ensure in place and lubricated before installing new injector

Get help to fix this fault by requesting a quote

Browse other New Holland codes