3072

New Holland 3072 – ECM: Cylinder 6 Injector Unclassifiable Error

Issue description

The Engine Control Module (ECM) has detected an anomaly with the fuel injector on cylinder 6 that does not fall into standard fault categories, such as a simple short or open circuit. This 'not plausible' error indicates the injector's performance is outside expected parameters, which can result from a mechanical issue within the injector, a complex electrical problem, or a fuel delivery issue. Specifically, it can be triggered by a general short circuit of the high side to the battery or ground that persists for several camshaft revolutions. As a protective measure, the ECM will shut off the affected cylinder.

Applies to these machines

  • T6.120
  • T6.140
  • T6.150
  • T6.155
  • T6.160
  • T6.165
  • T6.175
  • T6.180
  • T7.165
  • T7.170
  • T7.175
  • T7.185
  • T7.190
  • T7.200
  • T7.210
  • T7.220
  • T7.225
  • T7.230
  • T7.235
  • T7.245
  • T7.250
  • T7.260
  • T7.270
  • TS100A
  • TS110A
  • TS115A
  • TS125A
  • TS135A
  • T6020
  • T6030
  • T6050
  • T6070
  • T6080
  • T6090

Check the cause

  1. Review the ECM for other active or stored fault codes related to rail pressure, other injectors, or camshaft/crankshaft sensors to provide additional context.

  2. Inspect the wiring harness and connections for the cylinder 6 injector for chafing, corrosion, or loose terminals at both the injector and the ECM.

  3. Check fuel quality for contamination or varnish buildup, which is sometimes associated with Ultra-Low Sulfur Diesel (ULSD).

  4. Perform an injector leak-off test to check for excessive return fuel, which indicates internal wear or a stuck-open nozzle.

  5. Check battery voltage and main ground connections, as low voltage or poor grounds can cause ghost codes.

Repair steps

  1. Isolate the faulty cylinder

    With the engine running, carefully crack the high-pressure fuel line at each injector one at a time. If loosening the line to cylinder 6 causes no significant change in engine running characteristics, the cylinder is isolated as faulty.

  2. Swap injectors for diagnosis

    Swap the cylinder 6 injector with an injector from a known good cylinder (e.g., cylinder 5). Clear the fault codes and run the engine. If the fault moves to the new cylinder (e.g., code 3064 for cylinder 5), the injector is confirmed faulty. If code 3072 returns for cylinder 6, the issue is in the wiring harness or the ECM driver.

  3. Replace the fuel injector

    If the injector is confirmed faulty via the swap test, replace it with a new or remanufactured unit matching the OEM part number.

  4. Code the new injector

    After replacement, use a diagnostic tool to code the new common rail injector to the ECM (injector reset). This ensures the ECM recognizes the component and adjusts fuel delivery parameters correctly.

Parts you might need

(20)
  • Fuel Injector504128307
  • Fuel Injector

    500060542
  • Fuel Injector (Bosch Cross-Reference)

    0445120075
  • Fuel Injector (Bosch Cross-Reference)

    0445120073
  • Fuel Injector (Aftermarket)

    445120351

    Fits T7.210 from 2010 onwards. Cross-references NH 5801618038.

  • Remanufactured Fuel Injector

    87298764

    New Holland remanufactured part.

  • Fuel Injector (T9 12.9L F3DFA6 Engine)

    0445124014

    Bosch. Alternate CNH PN: 504388750. Verify fitment by serial number.

  • Fuel Injector (Iveco 445 Engines)

    2855491

    Alternate PNs: 0445120054 (Bosch), 504091504. Verify fitment by serial number.

  • CNH. Alternate Bosch PN: 0445110540. Verify fitment by serial number.

  • Fuel Injector (6.7L Common Rail Engines)

    0445120057

    Bosch. Alternate PNs: 2854608 (Case/NH), 504091505 (Iveco). Verify fitment by serial number.

  • Alternate PNs: 73379119, 47506932. Verify fitment by serial number.

  • OEM CNH/FPT Injector

    504255185

    Common-rail CRIN3-18 injector. Always verify the part number stamped on the original injector or check the machine's serial number against the parts catalog before ordering, as programming/coding is required upon installation.

  • Common-rail CRIN3-18 injector. Always verify the part number stamped on the original injector or check the machine's serial number against the parts catalog before ordering, as programming/coding is required upon installation.

  • OEM CNH/FPT Injector

    500060418

    Common-rail CRIN3-18 injector. Always verify the part number stamped on the original injector or check the machine's serial number against the parts catalog before ordering, as programming/coding is required upon installation.

  • OEM CNH/FPT Injector

    500061288

    Common-rail CRIN3-18 injector. Always verify the part number stamped on the original injector or check the machine's serial number against the parts catalog before ordering, as programming/coding is required upon installation.

  • Bosch Injector (New)

    0445120157

    Common-rail CRIN3-18 injector. Always verify the part number stamped on the original injector or check the machine's serial number against the parts catalog before ordering, as programming/coding is required upon installation.

  • Bosch Injector (Remanufactured)

    0986435564

    Common-rail CRIN3-18 injector. Always verify the part number stamped on the original injector or check the machine's serial number against the parts catalog before ordering, as programming/coding is required upon installation.

Get help to fix this fault by requesting a quote

Browse other New Holland codes