3078

New Holland 3078 – ECM: Cylinder 2 Injector Low Signal

Issue description

The Engine Control Module (ECM) has detected a low electrical signal from the electronic fuel injector for cylinder 2. This indicates a potential electrical fault with the wiring, connectors, or the injector's internal coil, rather than a mechanical failure. This condition affects the proper operation of the engine's fuel delivery system for that cylinder, which can result in engine misfires, erratic running, or excessive smoke.

Applies to these machines

  • Case 580N
  • Case 580SN
  • Case 590SN
  • Case Wheel Loaders
  • New Holland Tractors
  • New Holland Combines
  • Case Tractors
  • Case Combines

Check the cause

  1. Use an electronic service tool to clear codes, then operate the machine to confirm if fault code 3078 returns.

  2. Visually inspect the wiring harness and connectors between the ECM and the cylinder 2 injector for chafing, corrosion, loose connections, or bent/broken pins.

  3. Disconnect the ECM connector and inspect the specific pins for the cylinder 2 injector (e.g., pins 6 and 11) for cleanliness and proper seating.

  4. With the key on, check for a constant 12-volt supply at the injector connector, and use a noid light or test light to verify a ground pulse signal from the ECM while cranking or running.

  5. Measure the injector coil resistance across its two terminals; it should read between 0.5 and 1.0 Ω at 20°C (68°F).

Repair steps

  1. Isolate the Fault

    Follow the diagnostic checks above to determine if the fault lies with the wiring, connectors, or the injector itself.

  2. Repair wiring or connectors

    If wiring or connectors are damaged or lack proper voltage/pulse signals, repair or replace the affected harness section and clean or replace corroded connectors. Ensure all connections are secure.

  3. Replace fuel injector

    If the injector fails the resistance test (outside 0.5 - 1.0 Ω), clean the area, release common rail fuel pressure, and remove the faulty injector. Install the new injector with new seals/washers and torque the hold-down clamp and fuel lines to manufacturer specifications.

  4. Code the new injector

    If the injector was replaced, enter the new injector's calibration code into the ECM using an OEM Electronic Service Tool or compatible diagnostic tool (e.g., Jaltest) to ensure optimal performance.

  5. Verify repair

    Clear all fault codes from the ECM, start the engine, and operate the machine to confirm smooth operation and that code 3078 does not return.

Parts you might need

(13)
  • Bosch equivalent: 0445124036. Alternate OEM: 5801906153R

  • Bosch equivalent: 0445120057. Alternate OEM: 504091505

  • Bosch equivalent: 0445110457. Alternate OEM: 504091504

  • Fuel Injector (Boomer/Farmall)

    MT40265611

    Fits various Boomer and Farmall models

  • Genuine Bosch for Case/New Holland

  • Bosch Fuel Injector

    0-445-120-157

    Fitment for T8 and T9 series. Cross-references to New Holland part numbers 504255185 and 504255185R.

  • Remanufactured Fuel Injector

    504054021R

    Remanufactured OEM option.

  • Remanufactured OEM option.

  • Fuel Injector

    504275234

    New Holland OEM part number. Verification with a dealer is recommended.

  • Fuel Injector

    83964126

    New Holland OEM part number, also listed under Ford.

  • Fuel Injector, Cylinder 2

    73379119

    Listed for WORKMASTER and BOOMER compact tractors

  • Fuel Injector, Cylinder 2

    78500030

    Cross-referenced for various New Holland, Case IH, and Ford tractors (Alternate PN: 500307714)

  • Remanufactured Fuel Injector

    87298764

    Listed for various New Holland models including T8 series. Always verify the exact part number with a dealer using the machine's serial number.

Get help to fix this fault by requesting a quote

Browse other New Holland codes