3079

New Holland 3079 – ECU: Cylinder 2 Injector Circuit Short

Issue description

A short circuit has been detected in the injector cable for Cylinder 2, specifically a high-side-to-ground short. The Engine Control Module (ECM) logs this code when it detects a short circuit between the high-side driver wire for the cylinder 2 injector and the chassis ground. This condition affects the proper operation of the injector and can lead to engine performance issues, including misfires, rough running, and the presence of smoke.

Applies to these machines

  • B110C
  • B110D
  • B95C
  • B95CLR
  • B95CTC
  • B95D
  • C234
  • C238
  • C245
  • C334
  • C345
  • C362
  • L230
  • L234
  • L334
  • POWERSTAR 100
  • POWERSTAR 110
  • POWERSTAR 120
  • POWERSTAR 90
  • T4.100
  • T4.110
  • T4.120
  • T4.90
  • T5.100
  • T5.110
  • T5.120
  • T5.90
  • T8.275
  • T8.300
  • T8.320
  • T8.330
  • T8.350
  • T8.360
  • T8.380
  • T8.390
  • T8.410
  • T8.420
  • T8.435
  • T9.390
  • T9.435
  • WORKMASTER 95
  • WORKMASTER 105
  • WORKMASTER 120
  • CR7.90

Check the cause

  1. Visually inspect the wiring harness leading to the cylinder 2 fuel injector for chafing, melting, or damage. Pay close attention to areas where the harness may rub against the engine block or other components. Note that in one documented case, a rusted exhaust tip melted the ECU harness, causing an injector circuit short.

  2. Check for low voltage: Ensure the battery is fully charged (e.g., 12.6V instead of 12.1V), as a weak battery can trigger multiple 'ghost' codes. Verify that all main power and ground connections to the chassis are clean and tight.

  3. Perform a wiring harness test: disconnect the harness from the cylinder 2 injector, turn the key to 'ON', and use a multimeter to verify a constant 12-volt supply on one pin. Check continuity of the ground wire back to the ECU and inspect pins for corrosion or damage.

  4. Perform an injector resistance test: measure resistance across the two terminals on the disconnected injector and compare to manufacturer specifications to check for an out-of-specification reading, internal short, or open circuit.

Repair steps

  1. Isolate the fault

    Use the diagnostic checks to determine if the short circuit is located in the wiring harness or internally within the cylinder 2 fuel injector.

  2. Repair wiring harness

    If the wiring is shorted, chafed, or damaged, repair the affected wires. Ensure all repairs are properly insulated and secured away from heat sources or sharp edges to prevent future failures.

  3. Replace fuel injector

    If the injector fails the resistance test, disconnect the battery, clean the area, and remove the fuel lines and electrical connector. Remove the hold-down clamp or bolt and carefully extract the old injector. Clean the bore, and install the new injector with new seals/gaskets. Torque the hold-down clamp to spec and reconnect lines and connector.

  4. Clear fault codes

    Reconnect the battery and use a diagnostic tool to clear fault code 3079 from the ECU memory.

  5. Verify repair and calibrate

    Start the engine to ensure smooth operation and that the code does not return. Perform an injector trimming or calibration procedure if required by the specific engine system.

Parts you might need

(21)
  • Fuel Injector (OEM Remanufactured)

    504054021R

    For FPT/Iveco F5 series engines

  • Alternative OEM part number

  • Fuel Injector (OEM)

    5801792504

    Alternative OEM part number

  • Fuel Injector (FPT/Iveco)

    504385978

    Specified for F5CE5454 engines in Case and New Holland skid steers and track loaders

  • Fuel Injector (Bosch)

    0445120157

    Listed for 8.7L engines in various New Holland T8 and T9 series tractors

  • Fuel Injector (Bosch)

    0445110657

    Bosch alternative, verify fitment by serial number

  • Injector Wire Harness

    500347901

    Verify fitment with dealer

  • Injector Wire Harness

    47401109

    For F4D and F4H series engines

  • Fuel Injector

    504255185

    Bosch OEM. Cross-references to Bosch part numbers 0986435564 and 0445120157. Other possible part numbers include 504255185R, 5801470098, 504063465, 5801569141, 47506932, 5801790338R. Verify exact fitment with dealer using machine serial number.

  • Alternate OEM: 87708024, 504128307, 87581565R, 504054021R, 5801790338R, 87298764. Bosch: 0-445-120-157, 0445120075, 2855135.

  • Engine Control Unit (ECU)

    87709243

    Alternate OEM: 51496291, SBA185186180, 504122542, 76091914. Requires programming.

  • Injector Wiring Harness

    QTP-400337

    Aftermarket option

  • OEM example

  • Fuel Injector (Cylinder 2)

    87802430R

    OEM replacement for 87802430

  • Verify fitment by serial number.

  • Replaces 504128307. Verify fitment by serial number.

  • Verify fitment by serial number.

  • Common Rail Fuel Injector

    0445120075

    Bosch. Verify fitment by serial number.

  • Remanufactured. Verify fitment by serial number.

  • Verify fitment by serial number.

  • Fuel Injector (FPT 4.5L Engines)

    2855491

    Alternative OEM Part Number: 504091504. Bosch Part Number: 0445120054

Get help to fix this fault by requesting a quote

Browse other New Holland codes