3112

New Holland 3112 – ECU: Rail Pressure Sensor CP3 - Signal Above Maximum Range

Issue description

The Engine Control Unit (ECU) has detected a voltage signal from the common rail pressure sensor that is higher than the maximum acceptable limit. The ECU sends a 5-volt reference signal and expects a specific return voltage corresponding to fuel pressure. When this return voltage exceeds the threshold, it indicates an abnormal reading, typically caused by an open circuit, a short to the power supply, or an internal failure of the sensor itself. This triggers an amber warning and may cause the engine to enter a limp mode or derate to prevent potential damage from perceived high fuel pressure.

Applies to these machines

  • T5.120
  • T6.120
  • T6.125
  • T6.140
  • T6.145
  • T6.150
  • T6.155
  • T6.160
  • T6.165
  • T6.175
  • T6.180
  • T6020
  • T6030
  • T6040
  • T6050
  • T6060
  • T6070
  • T7.170
  • T7.185
  • T7.200
  • T7.210
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • T7030
  • T7040
  • T7050
  • T7060
  • TS125A
  • TS135A

Check the cause

  1. Visually inspect the wiring harness and connector for the rail pressure sensor for chafing, corrosion on the pins, or loose connections. Ensure the connector is securely fastened to the sensor.

  2. Check for any fuel leaks around the sensor and along the common rail.

  3. Ensure the battery is fully charged (around 12.6V) and that all main power and ground connections to the chassis and ECU are clean and tight.

  4. Perform a Reference Voltage Test: Disconnect the sensor connector. With ignition on (engine off), measure voltage between the 5V reference wire and a known good ground. Expected: 4.5-5.0 volts.

  5. Perform a Ground Circuit Test: With the connector disconnected, measure resistance between the ground terminal on the harness connector and the negative battery post. Expected: less than 0.5 Ohms.

  6. Perform a Signal Wire Test: Reconnect the sensor. With ignition on (engine off), back-probe the signal wire (expected: ~0.5V). With engine running at idle, voltage should be 1.2V - 1.5V. A voltage stuck high (e.g., 5V) indicates a faulty sensor or a short circuit to a power source in the signal wire.

Repair steps

  1. Prepare machine for service

    Turn off the engine and allow it to cool. Disconnect the negative battery terminal to prevent any electrical mishaps.

  2. Relieve fuel system pressure

    Consult the machine's service manual for the specific procedure to safely depressurize the fuel system. The common rail system operates under extremely high pressure, and failure to depressurize can result in serious injury.

  3. Remove the faulty sensor

    Locate the 3-terminal rail pressure sensor on the common fuel rail. Carefully unplug the electrical connector. Using the appropriate size wrench or socket, unscrew the old sensor. Have a clean cloth ready to catch any residual fuel.

  4. Install the new sensor

    Inspect the threads on the fuel rail for damage or debris. Thread the new sensor in by hand to avoid cross-threading, then tighten to the manufacturer's specified torque. Do not overtighten. Reconnect the electrical connector.

  5. Test and clear codes

    Reconnect the negative battery terminal. Turn the ignition on and check for fuel leaks around the new sensor. Start the engine, let it idle, and continue checking for leaks. Use a diagnostic tool to clear fault code 3112 from the ECU.

Parts you might need

(15)
  • Primary OEM part number (Bosch). 3 terminals, M18 x 1.50 thread. Alternative/Cross-reference numbers: 2854542, 2859145, 162000090747, 87829345, 87829346.

  • OEM New Holland/Case IH part for FPT engines (F5C, F5H), T6/T7 tractors, combines, and wheel loaders.

  • Superseded OEM part number, often cross-referenced with Bosch 0 281 002 824.

  • Fuel Rail Pressure Sensor

    0 281 002 824

    Bosch manufactured part.

  • Fuel Rail Pressure Sensor

    0 281 006 165

    Bosch manufactured part.

  • Rail Pressure Sensor

    504053982

    Bosch sensor. Fits TS110A, TS125A, TS135A. Alternate part numbers: 2831362, 2852780, 42567283, 504333094 (T6/T7 series), 2854542, 0281006199, 5801483105, 504343022, VV129A0057100, 73379120, 504358206.

  • CP3 High-Pressure Fuel Pump

    0445020093

    Bosch pump. Alternate part numbers: 504188076, 0445020175, 84385110, 4898921, 0445020334, 5801548002, 5801600539, 0445020335, 504063450. Used on 3.9L to 9.0L engines.

  • For T4 series and loaders with F5HFL engines

  • Fuel Common Rail Pressure Sensor (CNH / FPT)

    504043154

    Located directly on the high-pressure common rail. Ensure you are ordering the sensor for the rail, not the fuel control actuator/metering unit located on the CP3 pump itself.

  • Fuel Common Rail Pressure Sensor (Bosch)

    0281002964
  • Fuel Common Rail Pressure Sensor (Bosch)

    0281006249
  • Fuel Common Rail Pressure Sensor (Cummins Cross-Reference)

    4937283
  • Fuel Common Rail Pressure Sensor (Cummins Cross-Reference)

    5261237
  • Fuel Rail Pressure Sensor

    73379120

    CNH part. Fits various Boomer and Farmall compact tractors.

  • Fuel Rail Pressure Sensor

    VV129A0057100

    CNH part.

Get help to fix this fault by requesting a quote

Browse other New Holland codes