3141

New Holland 3141 – ECM: Too Low Fuel Supply Set Value

Issue description

The Engine Control Module (ECM) has detected a discrepancy in the expected fuel quantity balance, indicating insufficient fuel supply or a leak within the fuel system. This fault is logged when the actual fuel flow or pressure deviates from the value commanded by the ECM, which may also be interpreted as a fuel metering unit leakage. When active, this fault will typically force the machine into a stall mode or limp mode, limiting engine power and speed to prevent potential damage and affecting overall machine performance.

Applies to these machines

  • T4.75
  • T6 Series
  • T7 Series
  • T7.170
  • T7.185
  • T7.200
  • T7.210
  • T7.235
  • T9 Series
  • T9.390
  • T9.645
  • T9.670
  • T9.700
  • T9040
  • TJ380
  • TJ430
  • L221
  • L223
  • L225
  • L228
  • L230
  • C232
  • SR220
  • SR250
  • SV300

Check the cause

  1. Inspect fuel filters for restriction (primary cause of this fault)

  2. Check the fuel tank to ensure it is not empty, the fuel is clean, and the fuel cap is venting properly (a non-venting cap creates a vacuum)

  3. Thoroughly inspect all low-pressure fuel lines and quick-connect fittings from the tank to the injection pump for leaks, cracks, or loose connections

  4. Check for fuel system aeration by temporarily installing a clear hose or sight glass on the suction and return sides (bubbles indicate a suction-side leak)

  5. Evaluate the common rail pressure sensor and fuel rail pressure relief/bypass valve for faults or leaks

  6. Inspect the high-pressure fuel pump for wear

  7. Test fuel injectors for leaks (measure exhaust port temperature of each cylinder; a colder cylinder indicates poor combustion due to a fueling issue)

Repair steps

  1. Replace fuel filters

    Replace all primary and secondary fuel filters. Empty the old filters into a clear container to inspect for dirt, water, or debris. On models like the T7.235, also clean the gauze filter in the clear bowl.

  2. Bleed the fuel system

    Properly bleed the fuel system to remove any air that may have been introduced during the filter replacement.

  3. Repair air leaks

    If aeration was detected during diagnostics, trace the suction lines back from the lift pump to the tank to find and repair the source of the air leak.

  4. Replace rail pressure sensor or bypass valve

    If the low-pressure side is confirmed good and wiring/connectors are intact, replace the rail pressure sensor or the bypass valve.

  5. Replace high-pressure fuel pump

    If the high-pressure pump is failing, replace it. For example, on a T9.670: remove the breather cover and filter, use a puller to remove the gear from the tapered shaft (note that it may not have timing marks), unbolt the pump, and install the new one. Torque the gear nut to 195 ft-lbs. Place rags below the pump during removal to catch any dropped bolts.

Parts you might need

(8)
  • Alternative part numbers: 87329736, 504287009

  • Specific to T9.670

  • For T6 & T7 Series. Bosch cross-references: 2854542, 0281002930

  • High-Pressure Fuel Pump (T9 Series)

    87282080

    Alternative part numbers: 0445020223 (Bosch), 47669601

  • High-Pressure Fuel Pump (L-Series)

    5801470100

    For L-Series Skid Steers

  • General lift pump used on various models, replaces numerous older part numbers

  • Fuel Rail Pressure Relief/Bypass Valve

    8097663

    For L230 and others. Replaces 504253059. Alternative relief valve: 5801474163

  • For L230 Skid Steer

Get help to fix this fault by requesting a quote

Browse other New Holland codes