3176

New Holland 3176 – ECU: Metering Unit Setpoint Implausible In Overrun

Issue description

The Engine Control Unit (ECU) has detected an implausible signal from the fuel metering unit during engine overrun conditions (when the vehicle's momentum is driving the engine and the throttle is closed). This indicates a potential inconsistency between the expected and actual behavior of the metering unit during this operating phase. Specifically, the high-pressure pump delivery quantity exceeds a predefined threshold based on the expected pressure in overrun mode, which can be caused by low-pressure fuel circuit issues or high-pressure component failures.

Applies to these machines

  • T6
  • T7
  • T6000
  • T7000
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • CR
  • CX
  • Magnum 235
  • Magnum 340
  • Puma
  • Axial-Flow

Check the cause

  1. Check the fuel level to ensure the tank is not empty or very low, which can introduce air into the system

  2. Visually inspect all fuel lines from the tank to the high-pressure pump for leaks, damage, or loose connections

  3. Check for air in the fuel system by installing a clear sight tube on the low-pressure fuel supply line just before the high-pressure pump and observing for bubbles while the engine is running

  4. Inspect primary and secondary fuel filters for clogs or restrictions that could starve the high-pressure pump

  5. Test the low-pressure fuel supply with a pressure gauge to verify the lift pump is delivering adequate and stable pressure under load

  6. Inspect the 2-pin electrical connector on the fuel metering unit for corrosion, bent pins, moisture, or debris

  7. Check the wiring harness leading to the metering unit for any signs of rubbing, chafing, or breaks

  8. Perform a metering unit actuator test using the Electronic Service Tool (EST) and listen for an audible click from the valve

Repair steps

  1. Release fuel pressure

    Ensure the fuel system is depressurized according to the manufacturer's safety guidelines before opening any high-pressure fuel lines.

  2. Remove fuel metering unit

    Disconnect the electrical connector from the fuel metering unit. Clean the area around the pump thoroughly to prevent contamination. Remove the screws securing the metering unit to the high-pressure pump and carefully extract it.

  3. Install new metering unit

    Lubricate the O-rings on the new metering unit with clean diesel fuel or a suitable lubricant. Carefully install the new unit into the high-pressure pump and tighten the retaining screws to the specified torque.

  4. Reconnect and bleed system

    Reconnect the electrical connector. Prime the low-pressure fuel system thoroughly to bleed all air that may have entered during the repair.

  5. Clear Fault Codes

    Use the appropriate diagnostic tool to clear the 3176 fault code from the ECU.

  6. Test Operation

    Start the engine and allow it to run, checking for any fuel leaks. Monitor the system to ensure the fault code does not return.

Parts you might need

(18)
  • OEM CNH Industrial part. Supersedes/Replaces: 42541851, 1638153, 4937597, 0928400481. Verify fitment against machine serial number.

  • Primary and Secondary Fuel Filters

    Replace as a matter of course during diagnosis to rule out restrictions.

  • Listed for Case IH / Ford / New Holland

  • Fuel Metering Unit / Fuel Control Actuator (Bosch)

    1462C00998

    Associated with Bosch CP4 pumps used in FPT engines

  • Listed for New Holland T8.390. Note: The Fuel Sender Unit is for the fuel gauge and is distinct from the Fuel Metering Unit that controls pressure.

  • Listed for various New Holland models. Note: The Fuel Sender Unit is for the fuel gauge and is distinct from the Fuel Metering Unit that controls pressure.

  • Fuel Metering Unit (Parts set, CR pump)

    F00N210061

    Listed for New Holland T9.530 with FPT engine

  • Fuel Control Actuator / Fuel Metering Valve

    1110010022

    Referenced for New Holland Iveco applications

  • Bosch Fuel Metering Valve

    0928400481

    Compatible with various New Holland, Case IH, and Iveco applications

  • Fuel Metering Unit / FCA / MPROP

    0928400681

    Bosch OEM Part Number (Common CP3 variant)

  • Fuel Metering Unit / FCA / MPROP

    0928400715

    Bosch OEM Part Number (Common CP3 variant)

  • Fuel Metering Unit / FCA / MPROP

    0928400738

    Bosch OEM Part Number (Common CP3 variant)

  • Fuel Metering Unit / FCA / MPROP

    1465ZS0068

    Bosch OEM Part Number (Common CP3 variant)

  • Pressure Limiting Valve / PRV

    1110010013

    Bosch OEM Part Number

  • High-Pressure Fuel Pump Assembly

    0445020175

    Bosch OEM Part Number

  • CNH OEM Part Number

  • CNH OEM Part Number

  • CNH OEM Part Number

Get help to fix this fault by requesting a quote

Browse other New Holland codes