3196

New Holland 3196 – ECU: Cylinder 3 Injector Circuit - Open Load Engine

Issue description

This fault code indicates that the Engine Control Unit has detected an "Open Load" (open circuit) in the electrical circuit for the fuel injector on cylinder #3. This means electrical current is not flowing through the injector solenoid coil, preventing the injector from firing. The underlying condition is typically a broken wire, a disconnected or corroded harness connector, or an internal failure (open coil) within the fuel injector itself.

Applies to these machines

  • T4.90
  • T4.100
  • T4.110
  • T4.120
  • T5.90
  • T5.100
  • T5.110
  • T5.120
  • POWERSTAR 90
  • POWERSTAR 100
  • POWERSTAR 110
  • POWERSTAR 120
  • WORKMASTER 95
  • WORKMASTER 105
  • WORKMASTER 120
  • B110C
  • B110D
  • B95C
  • B95CLR
  • B95CTC
  • B95D
  • C234
  • C238
  • C245
  • C334
  • C345
  • C362
  • L230
  • L234
  • L334

Check the cause

  1. Perform a visual inspection of the wiring harness and connectors associated with the cylinder 3 fuel injector, looking for any signs of damage, such as chafing, corrosion, or loose connections.

  2. Disconnect the electrical connector at the cylinder 3 injector and the corresponding connector at the ECU. Inspect the pins and sockets for any signs of corrosion, dirt, or damage. Ensure a snug and secure connection when re-seated.

  3. Using a multimeter, check the continuity of the wires running between the ECU and the cylinder 3 injector connector to verify there are no breaks.

  4. With the injector disconnected, use a multimeter to measure the resistance across the two terminals of the injector and compare to manufacturer specifications. An infinite resistance reading indicates an open circuit within the injector.

  5. While the engine is running (if possible), carefully wiggle the wiring harness and connectors for the cylinder 3 injector. If the engine's running condition changes, it indicates an intermittent connection.

Repair steps

  1. Isolate the Faulty Component

    Based on the diagnostic checks, determine if the fault lies with the wiring, the connector, or the injector itself.

  2. Repair or Replace Wiring/Connectors

    If a break or corrosion is found in the wiring or connectors, repair or replace the affected section of the harness. Ensure all connections are clean and secure.

  3. Replace the Fuel Injector

    If the injector is identified as the faulty component, replace it. It is recommended to replace the injector seal and any associated hardware at the same time.

  4. Injector Reset/Calibration

    After replacing a fuel injector, perform an injector reset or calibration using a compatible diagnostic tool so the ECU recognizes the new component and adjusts fuel delivery parameters.

  5. Clear Fault Codes

    Once the repair is complete, use a diagnostic tool to clear the active fault code from the ECU's memory.

  6. Verify the Repair

    Start the engine and let it run to ensure that the fault code does not reappear and that the engine is operating smoothly.

Parts you might need

(22)
  • Fuel Injector5801790338
  • Fuel Injector

    5801792504
  • Fuel Injector

    504385978
  • Fuel Injector (Remanufactured)

    504054021R
  • Fuel Injector (Bosch)

    0445110657
  • Fuel Injector (Bosch)

    0-445-110-657
  • Fuel Injector500307714
  • Fuel Injector

    504054021
  • For FPT F5C / F5H 3.4L Engines. Manufacturer: Bosch / FPT Genuine.

  • Fuel Injector Assembly

    5802820879

    For FPT F5C / F5H 3.4L Engines. Manufacturer: Bosch / FPT Genuine.

  • Fuel Injector Assembly

    504091505

    For FPT NEF 4.5L / 6.7L Engines. Manufacturer: Bosch.

  • For FPT NEF 4.5L / 6.7L Engines. Manufacturer: Bosch.

  • Fuel Injector Assembly

    2855491

    For FPT NEF 4.5L / 6.7L Engines. Manufacturer: Bosch.

  • Fuel Injector Assembly

    0445120057

    For FPT NEF 4.5L / 6.7L Engines. Manufacturer: Bosch.

  • Fuel Injector Assembly

    0445120054

    For FPT NEF 4.5L / 6.7L Engines. Manufacturer: Bosch.

  • OEM Iveco. Alternate OEM numbers: 2855135, 0445120075 (Bosch 6.7L)

  • Fuel Injector (STX Series / Case IH)

    0986441027

    Remanufactured. Cross-references to OEM numbers 504287106, 504128354, 504099014

  • Fuel Injector (T8 & T9 Series)

    0-445-120-157

    OEM Bosch. Cross-references to 504255185. Alternate Reman: 0986435532 (For Cummins ISC 8.3L)

  • Engine Wiring Harness

    51422017

    Verify fitment by serial number

  • Engine Wiring Harness

    47523049

    Verify fitment by serial number

  • Engine Wiring Harness

    86508264

    Fits older models like 8670, 8770

  • Engine Wiring Harness

    86603919

    Fits various skid steer models

Get help to fix this fault by requesting a quote

Browse other New Holland codes