3302

New Holland 3302 – ECM: Cylinder 3 Injector Signal Not Plausible

Issue description

The Engine Control Module (ECM) has detected an electrical signal from the fuel injector circuit of cylinder 3 that is outside of its expected or plausible range. This occurs when the feedback from the cylinder 3 injector does not match the command sent by the ECM, indicating a potential problem with the communication, electrical operation, or wiring of the injector rather than a mechanical failure.

Applies to these machines

  • T6020
  • T7.170
  • T7.200
  • T7030
  • T7040
  • T7050
  • T7060
  • T7070
  • Puma
  • Maxxum

Check the cause

  1. Inspect the wiring harness leading to the fuel injector on cylinder 3 for signs of damage (chafing, melting, cracking, corrosion) and ensure the electrical connector is securely fastened with clean, undamaged pins.

  2. Check for any accompanying misfire codes (e.g., P0303) or other injector circuit faults to confirm a combustion issue on cylinder 3.

  3. Verify power and ground to the injector using a multimeter or a noid light (which should flash when cranking or running) to ensure the ECM is sending the command signal.

  4. Perform a 'wiggle test' by carefully wiggling the wiring harness and connector for the cylinder 3 injector while the engine is idling to check for intermittent connections.

  5. Check battery voltage to ensure it is fully charged (above 12.1V) and verify that main chassis and engine ground straps are clean and tight to prevent ghost codes.

Repair steps

  1. Isolate the Fault

    If the initial wiring checks do not reveal an obvious issue, swap the cylinder 3 fuel injector with an injector from an adjacent cylinder (e.g., cylinder 2 or 4).

  2. Clear Fault Codes

    After swapping the injectors, clear all fault codes from the ECM using a diagnostic tool.

  3. Operate the Engine

    Start the engine and let it run.

  4. Re-check for Faults

    If the fault code moves to the cylinder where the suspect injector was installed (e.g., the fault is now 3304 for cylinder 4), the fuel injector itself is faulty and should be replaced. If the fault code remains as 3302 for cylinder 3, the problem lies within the wiring harness or the ECM's injector driver circuit.

  5. Test Injector Resistance

    If the injector is suspected to be faulty, measure the resistance across its terminals with a multimeter (when disconnected) and compare it to the manufacturer's specifications.

  6. Final Repair

    Replace the identified faulty component (the fuel injector or repair the wiring). If replacing the injector, it is critical to also replace any one-time-use seals or high-pressure lines as per manufacturer requirements. Program the new injector's calibration code into the ECM if required.

Parts you might need

(10)
  • Bosch OEM. Also listed as 0445120075, 2855135, 504117273, 0986435530. Fits various T6/T7, Puma, and Maxxum models.

  • Fits T6020, T7.170, T7.200, T7030-T7070.

  • Remanufactured option. Core charge part number JC908507 may apply.

  • Fuel Injector (Cylinder 3)

    5801453888

    Includes copper wire/seal

  • Fuel Injector (Cylinder 3)

    504091505

    Alternative OEM Part Number for 6.7L Iveco/New Holland engines

  • Alternative OEM Part Number for 6.7L Iveco/New Holland engines

  • Fuel Injector (Cylinder 3)

    0445120057

    Bosch Equivalent Part Number

  • Fuel Injector (Cylinder 3)

    0986435552

    Bosch Equivalent Part Number

  • Engine Control Unit (Bosch EDC7)

    0281010253

    Only replace if the ECU hardware is proven to be the source of the signal failure. Requires programming/cloning to the vehicle's immobilizer system

  • Only replace if the ECU hardware is proven to be the source of the signal failure. Requires programming/cloning to the vehicle's immobilizer system

Get help to fix this fault by requesting a quote

Browse other New Holland codes