3436

New Holland 3436 – ECM: SCR System Inducement Locked

Issue description

Fault code 3436 indicates that the Selective Catalytic Reduction (SCR) system has entered a locked state due to a persistent, unresolved fault within the aftertreatment system. This is an enforcement action taken by the engine's control system to prevent severe damage and ensure emissions compliance. When active, the machine experiences a significant engine power derate (limp mode) and may be limited to idle speed or face rolling shutdowns. The system requires a specific reset procedure using an Electronic Service Tool (EST) to restore normal operation after the underlying cause is rectified.

Applies to these machines

  • T4
  • T5
  • T6
  • T7
  • T8
  • T7.165
  • T6.160
  • Puma
  • Maxxum
  • Optum
  • Puma 150
  • Case SR270
  • Harvesters
  • Sprayers
  • Skid Steers

Check the cause

  1. Read all active and inactive fault codes using an EST or J1939 scanner to identify the primary SCR/DEF fault triggering the inducement.

  2. Check the DEF tank level, as a low level is a common trigger.

  3. Visually inspect the DEF quality (should be crystal clear with a faint ammonia smell) and use a refractometer to verify urea concentration is between 31.8% and 33.2%.

  4. Investigate primary SCR system faults indicated by other codes, such as DEF dosing unit/pump issues, NOx sensor erratic data, DEF injector circuit failures, heater circuit faults, or CAN bus communication errors.

  5. Carefully inspect the wiring harness and connectors for the DEF pump, NOx sensors, and DEF injector for chafing, corrosion, melting, or loose pins.

  6. Check the DEF supply module filter (typically a 170-micron cartridge) for clogs.

  7. Remove and inspect the DEF injector nozzle for crystallization or blockage.

Repair steps

  1. Repair primary fault

    Based on diagnostic checks, perform necessary repairs for the primary fault. This may include draining and refilling contaminated DEF, replacing a faulty NOx sensor (healthy heater circuit is 2-6 Ohms), replacing a failed DEF pump, cleaning/replacing a crystallized DEF injector (flow test should yield 40-55ml over 2 minutes), or repairing damaged wiring.

  2. Connect diagnostic tool

    Connect a laptop with New Holland EST software (or a compatible high-level tool like Jaltest) to the machine's diagnostic port and navigate to the engine controller (e.g., EDC 17 CV41 + Denox 2.2).

  3. Perform SCR system resets

    In the service or maintenance functions menu, perform the 'Unlock Induces / SCR Inducement Reset'. Also perform the 'OxCat Reset / SCR Value Reset', 'SCR Catalyst Reset', and 'Reset NOx Sensor Learned Values' (if NOx sensors were replaced).

  4. Clear fault codes

    After performing the resets, command a clear of all active and inactive fault codes.

  5. Perform drive cycle or forced regeneration

    Operate the machine under load for 20-45 minutes to allow the SCR system to reach operating temperature, or initiate a forced DPF regeneration to complete the relearning process.

  6. Verify repair

    Re-read the fault codes to ensure that the 3436 code and all primary faults have been cleared and do not return. Verify full engine power is restored.

Parts you might need

(4)
  • OEM New Holland part (Alternate numbers: 84246892, 5802855460, 47565934; Bosch: 0444042210, 0444022021). Used on T-Series and Puma tractors. May require programming.

  • 170-micron filter located in the DEF pump/supply module for T5, T6, T7, Maxxum, and Puma series.

  • NOx Sensor

    Upstream (inlet) and downstream (outlet) sensors are not interchangeable. Must be sourced using the machine's parts catalog.

  • DEF Injector / Dosing Valve

    A healthy dosing valve typically has a resistance between 10-12 ohms. Must be sourced using the machine's parts catalog.

Get help to fix this fault by requesting a quote

Browse other New Holland codes