3794

New Holland 3794 – ECU: Intake Air Pressure Sensor: Plausibility Check Failure

Issue description

The Engine Control Unit (ECU) has determined that the signal from the intake air pressure sensor is illogical or irrational when compared with other related engine parameters, such as atmospheric pressure, engine speed, and throttle position. This plausibility fault indicates a discrepancy in the data's logical consistency rather than a simple electrical open or short circuit. The affected sensor is often a combined Manifold Air Pressure and Temperature (T-MAP) sensor used to calculate air density, determine the correct air-fuel ratio, and control turbocharger boost levels.

Applies to these machines

  • B110C
  • B95C
  • B95CLR
  • B95CTC
  • C185
  • C227
  • C232
  • C237
  • C238
  • C327
  • C332
  • C337
  • L180
  • L185
  • L223
  • L225
  • L230
  • W80BTC
  • T4.100F
  • T4.100V
  • T4.110F
  • T4.110V
  • T4.80F
  • T4.80V
  • T4.90F
  • T4.90V
  • TD5030
  • W50C
  • W60C
  • W60D
  • W70C
  • W80C
  • T7.165
  • T6.120
  • TS100A
  • T6020
  • T5.95
  • TC5070
  • CX5080

Check the cause

  1. Carefully inspect the intake air pressure sensor, its connector, and the wiring harness for any signs of damage, corrosion, or loose connections

  2. Inspect the intake manifold and all associated hoses for any cracks, loose clamps, or other potential sources of air leaks that could cause implausible pressure readings

  3. Using a multimeter, confirm that the sensor is receiving the correct voltage from the ECU

  4. Ensure the sensor has a solid ground connection

  5. With the engine running, or by applying vacuum/pressure with a hand pump, monitor the signal voltage from the sensor to see if it changes and if the readings are logical for the conditions

Repair steps

  1. Repair wiring and air leaks

    If the visual inspection reveals any damaged wiring, corroded connectors, or air leaks, repair these issues first. Clear the fault code and operate the machine to see if the code returns.

  2. Test the sensor

    If no obvious issues are found, test the sensor by comparing its readings to a known good sensor or to a manual pressure gauge.

  3. Replace the sensor

    If the sensor is determined to be faulty, disconnect the negative battery terminal. Disconnect the electrical connector, carefully remove the sensor from the intake manifold, install the new sensor ensuring it is seated correctly, and reconnect the electrical connector and battery.

  4. Clear fault codes

    After the repair is complete, use a diagnostic tool to clear the fault code from the ECU's memory.

  5. Verify repair

    Start the engine and let it run to ensure the fault code does not reappear. Check for proper engine performance.

Parts you might need

(16)
  • Verify fitment with vehicle serial number

  • Also replaces 504088431 and 504245257. Bosch cross-reference 0281006028

  • Verify fitment with vehicle serial number

  • Also replaces 47361730 and 5801483105

  • Intake Air Pressure Sensor / Boost Pressure Sensor / MAP Sensor

    5802231983

    4-pin sensor that often features an integrated temperature sensor. Cross-references with Case IH, Iveco, and Cummins applications.

  • 4-pin sensor that often features an integrated temperature sensor. Cross-references with Case IH, Iveco, and Cummins applications.

  • Intake Air Pressure Sensor / Boost Pressure Sensor / MAP Sensor

    0281006102

    Bosch OEM part. 4-pin sensor that often features an integrated temperature sensor. Cross-references with Case IH, Iveco, and Cummins applications.

  • Intake Air Pressure Sensor / Boost Pressure Sensor / MAP Sensor

    0281002420

    Bosch OEM part. 4-pin sensor that often features an integrated temperature sensor. Cross-references with Case IH, Iveco, and Cummins applications.

  • Intake Air Pressure Sensor / Boost Pressure Sensor / MAP Sensor

    0281006123

    Bosch OEM part. 4-pin sensor that often features an integrated temperature sensor. Cross-references with Case IH, Iveco, and Cummins applications.

  • Intake Air Pressure Sensor / Boost Pressure Sensor / MAP Sensor

    0281002316

    Bosch OEM part. 4-pin sensor that often features an integrated temperature sensor. Cross-references with Case IH, Iveco, and Cummins applications.

  • Used on a broad range of Case IH and New Holland equipment.

  • Found on CR/CX combines and T7/T8 tractors.

  • Intake Air Pressure Sensor (Aftermarket)

    QTP-44438

    Fits TG, T8000, and T9000 series tractors.

  • For New Holland Agriculture

  • For New Holland Construction

  • Air Pressure (T2) Sensor

    MT40273639

    Verify correct part number using machine serial number

Get help to fix this fault by requesting a quote

Browse other New Holland codes