3959

New Holland 3959 – ECM: Injector 2 And/Or 3 - Shorted To High

Issue description

The Engine Control Module (ECM) has detected an abnormally high voltage on the control circuit for fuel injector 2 and/or 3. This indicates that the control or ground wire for the injector has shorted to a power source. This electrical fault prevents the affected injectors from firing correctly, resulting in engine performance issues.

Applies to these machines

  • T6
  • T7
  • T8
  • T9
  • T1804
  • T2104
  • T6020
  • T7030
  • T7040
  • T7050
  • T7060
  • T7070
  • CR8.80
  • CR8.90
  • CR9.80
  • CR9.90
  • CR9040
  • B95B
  • B100B
  • B110B
  • D85B
  • D95B
  • 675 TA
  • 675 TA/CB
  • T9.480
  • T9.530
  • T9.565
  • T7.170
  • T7.200

Check the cause

  1. Visually inspect the wiring harness leading to injectors 2 and 3 for chafing, melting, or damage that could cause a short to a power source.

  2. Check for corrosion or damage at the injector connectors and the ECM connector.

  3. With the key on and engine off, use a multimeter to check the voltage at the electrical connector for injectors 2 and 3 (one wire should typically have a constant voltage supply).

  4. Disconnect the wiring harness from the injectors and ECM, and check for continuity between the injector connector and ECM connector to rule out open circuits.

  5. Test for shorts by checking for continuity between the injector signal wire and the power supply wire, as well as between the signal wire and chassis ground (there should be no continuity).

  6. Disconnect the injector and measure the resistance across its terminals, comparing the reading to a known good injector to check for internal coil failure.

Repair steps

  1. Isolate the fault

    Determine if the fault is with a single injector or both. If the fault is active, disconnect injector 2 and see if the code changes or becomes inactive. Repeat for injector 3 to pinpoint the source of the short.

  2. Repair wiring harness

    If a short is found in the wiring harness during testing, repair the damaged section. Ensure the repaired section is properly insulated and protected from future damage.

  3. Replace faulty injector

    If the wiring is confirmed to be good, the fault likely lies within the injector itself (internal short). Replace the faulty injector(s). It is recommended to replace the injector connector at the same time, as a faulty connector can cause similar issues.

  4. Clear codes and test

    After repairs are complete, clear the fault codes from the ECM and run the engine to ensure the fault does not return.

Parts you might need

(13)
  • Manufacturer: Iveco.

  • Manufacturer: Iveco.

  • Fuel Injector (T8, T9 series)

    0-445-120-157

    Manufacturer: Bosch.

  • Fuel Injector (T8, T9 series)

    504255185

    OEM Number replaced by Bosch 0-445-120-157.

  • OEM Number replaced by Bosch 0-445-120-157.

  • New Holland Part Number. For FPT Cursor 13 engines.

  • Fuel Injector (Combines and T9 series)

    0-445-124-036

    Bosch Part Number. For FPT Cursor 13 engines.

  • For T1804, T2104, T6020, T7.170, T7.200, T7030-T7070.

  • Replaced by 87802430R.

  • Fuel Injector (Construction 675 TA)

    87802430R

    Replaces 87802430.

  • Fuel Injector (Backhoes/Dozers)

    2855491

    For Iveco 445 Engines.

  • Fuel Injector (Backhoes/Dozers)

    0445120054

    For Iveco 445 Engines.

  • Fuel Injector (Backhoes/Dozers)

    504091504

    For Iveco 445 Engines.

Get help to fix this fault by requesting a quote

Browse other New Holland codes