3981

New Holland 3981 – ECU: DOC-In Temperature Below 220°C During Regeneration

Issue description

The Diesel Oxidation Catalyst (DOC) is the first section of the aftertreatment assembly, responsible for utilizing a chemical process to break down pollutants. For a successful exhaust regeneration to occur, the exhaust gas entering the DOC must reach a minimum operational temperature threshold. This fault code triggers when the system detects that the exhaust gas temperature at the DOC inlet has failed to reach 220 °C (428 °F) while an active regeneration cycle is being attempted.

Applies to these machines

  • L213
  • L215
  • L216
  • L218
  • L220
  • L223
  • L225
  • L230
  • C227
  • C232
  • C234
  • C237
  • C238
  • C245

Check the cause

  1. Verify operating conditions: Ensure the machine is not exclusively used for short trips or low engine loads, check that a regeneration-inhibit switch is not activated, and ensure high-demand systems (AC/PTO) are not preventing heat buildup

  2. Check for related fault codes using a diagnostic scanner, specifically looking for codes 1800 and 1801 (DOC Intake Temperature Sensor out of range), or EGR/pressure sensor faults

  3. Visually inspect the DOC inlet temperature sensor and its wiring harness for damage, corrosion, or loose connections

  4. Test wiring continuity from the sensor back to the ECU connector and check for shorts to ground using a multimeter

  5. Inspect the exhaust system for leaks between the engine manifold and the DOC inlet that could allow cold air to enter and lower exhaust gas temperatures

  6. Inspect upstream components that could prevent the engine from reaching operating temperature or cause excessive soot (e.g., thermostat stuck open, leaking fuel injectors, or a clogged/malfunctioning EGR valve)

Repair steps

  1. Address related fault codes

    Diagnose and repair any other active or stored fault codes first, as they may be the root cause preventing regeneration temperatures.

  2. Repair wiring issues

    Repair or replace damaged wiring or corroded connectors at the DOC inlet temperature sensor harness. Ensure all connections are clean and secure.

  3. Replace DOC inlet temperature sensor

    If the sensor fails a resistance test or provides inaccurate readings on a scan tool, replace it. Apply a high-temperature anti-seize compound to the threads of the new sensor, being careful not to get any on the sensor probe.

  4. Repair exhaust leaks

    Seal any exhaust leaks found between the engine manifold and the DOC inlet by replacing gaskets or affected exhaust components.

  5. Perform a forced regeneration

    Use a diagnostic tool to initiate a forced or stationary regeneration. Monitor the DOC inlet temperature via live data to confirm it reaches and maintains the required 220°C for a successful cycle.

  6. Clean or replace DOC/DPF

    If a forced regeneration does not resolve the issue due to severe soot overloading or face-plugging, remove the aftertreatment components for professional cleaning or replacement.

Parts you might need

(12)
  • DOC Inlet Temperature Sensor

    SBA185746130

    Also listed as 185746130 or 84535501. Listed for Skid Steer Loaders L213, L215, L216, L218, L220, L223. Verify with serial number.

  • Listed for Compact Track Loaders C227, C232, C238. Verify with serial number.

  • Temperature Sensor

    87341875

    Generic temperature sensor for New Holland machines. Verify fitment with serial number.

  • Also listed as SBA385720010 or 87761510. Note: This is for a different application (coolant) but demonstrates the OEM part number format.

  • For FPT engines in T6/T7 tractors and CR/CX combines; verify fitment by serial number.

  • For FPT engines in T6/T7/T8 tractors and CR/CX combines; verify fitment by serial number.

  • Verify fitment by serial number.

  • Sensor504264463

    For FPT engines; verify fitment by serial number.

  • Exhaust Gas Temperature Sensor (EGTS) / DOC Inlet Temperature Sensor

    5802391885

    New Holland Agriculture / Iveco

  • Temperature Sensor Mount

    47489202

    If damaged during removal

  • DOC Clamp

    47428312

    If damaged during removal

Get help to fix this fault by requesting a quote

Browse other New Holland codes