4103

New Holland 4103 – Rear Electro-Hydraulic Remotes: Rear Remote No. 1 – Not Commanded Neutral on Power-Up

Issue description

The electronic control system has detected that the spool for the number one rear electro-hydraulic remote (EHR) valve is not in the neutral position when the tractor is powered on. During its startup sequence, the controller commands the valve to be in neutral; if the valve's position sensor reports a position other than neutral, this fault is logged. This condition switches the remote to a failsafe mode, preventing the operation of the affected remote and potentially affecting the proper operation of the hydraulic system connected to it.

Applies to these machines

  • T6 Series
  • T7 Series
  • T8 Series
  • T9 Series
  • T6000 Series
  • T7000 Series

Check the cause

  1. Verify that the operator was not activating the remote lever during tractor startup

  2. Restart the tractor completely to see if a simple power cycle clears an intermittent fault

  3. Check the diagnostic menu for other active fault codes (e.g., 4104 under-voltage, 4105 over-voltage, 4106/4107 incorrect spool movement) to help pinpoint the issue

  4. Visually inspect the wiring harness and connectors leading to the number one rear remote valve and the operator's armrest controls for damage, corrosion, or loose connections (specifically check the plug under the cab on the right-hand side)

  5. Utilize the tractor's diagnostic 'H' menu to test the functionality of the switches in the armrest control lever

  6. Swap electrical connectors with an adjacent remote valve (e.g., remote #2) to isolate the issue. If the fault moves to remote #2, the valve's electronic module or position sensor is likely faulty. If the 4103 fault remains on remote #1, the issue is more likely in the wiring or the main controller

Repair steps

  1. Repair wiring

    If damaged wiring or corroded connectors were found during diagnostic checks, repair or replace them as necessary. Ensure all connections are clean and secure.

  2. Calibrate the remote valve

    Access the diagnostic 'H' menu to recalibrate the remote valve. Put the system into calibration mode, set the flow control to maximum, and move the control lever to its full extent and float positions to re-synchronize the lever and the valve.

  3. Replace the remote lever or switch

    If diagnostic tests point to a faulty switch in the armrest control lever (paddle or joystick), replace the affected switch or lever assembly.

  4. Replace the spool position sensor

    If the sensor is faulty (the most common cause), relieve all hydraulic pressure from the system. Disconnect the electrical connector from the sensor on the #1 remote valve block, unbolt and remove the sensor, and install the new sensor ensuring seals are correctly seated. Reconnect the electrical connector.

  5. Replace the remote valve section

    If the position sensor is not available as a separate part or if the valve body itself is determined to be faulty (e.g., a sticking spool), replace the entire remote valve section.

  6. Perform post-repair calibration

    After replacing the position sensor, control lever, or the entire valve, perform the remote valve calibration procedure via the 'H' menu to ensure proper operation and to clear the fault code.

Parts you might need

(6)
  • Supersedes 84385135, 87312136, 47128303, 5184312. Fits various T6, T7, T6000, T7000, Maxxum, and Puma models.

  • Electro-Hydraulic Remote Lever (with harness)

    48002177

    Verify correct part number for specific machine armrest configuration.

  • Verify correct part number for specific machine armrest configuration.

  • Verify correct part number for specific machine armrest configuration.

  • Joystick Control Lever

    84208937

    Verify correct part number for specific machine armrest configuration.

  • Fits various T6000 series and Case IH Maxxum/Puma models. Part numbers will vary by tractor series.

Get help to fix this fault by requesting a quote

Browse other New Holland codes