4108

New Holland 4108 – EHR / TMF: Rear Remote No. 1 Float Position Not Reached

Issue description

The electronic control system has detected that the No. 1 rear remote valve has failed to reach the float position when commanded. This indicates that the hydraulic valve spool has not moved to the position allowing hydraulic fluid to flow freely in and out of the remote couplers, which is necessary for implements that need to follow ground contours. This fault is logged against the electro-hydraulic remote (EHR) controller, which is part of the tractor's overall electronic management system.

Applies to these machines

  • T6010
  • T6020
  • T6030
  • T6040
  • T6050
  • T6060
  • T6070
  • T6080
  • T6090
  • T6.120
  • T6.140
  • T6.150
  • T6.155
  • T6.160
  • T6.165
  • T6.175
  • T6.180
  • T7.170
  • T7.185
  • T7.200
  • T7.210
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • T7030
  • T7040
  • T7050
  • T7060
  • T8.275
  • T8.300
  • T8.330
  • T8.360
  • T8.390
  • T9.390
  • T9.450
  • T9.505
  • T9.560
  • T9.615
  • T9.670
  • TM120
  • TM130
  • TM140
  • TM155
  • TM175
  • TM190

Check the cause

  1. Review other active fault codes related to the rear remote valves (e.g., 4111 for potentiometer faults, 4106/4107 for spool movement issues, or 4104/4105 for voltage issues) to help pinpoint the root cause

  2. Inspect the wiring harness and connectors leading to the number 1 rear remote valve for visible damage, corrosion, or loose connections

  3. Ensure the manual override on the valve is not engaged, as this can trigger related fault codes (e.g., 4109)

  4. Check the hydraulic fluid level and condition, as contaminated or low fluid can affect hydraulic performance

  5. Attempt to recalibrate the rear remote valves, as a lost or corrupt calibration is a common cause for this issue

Repair steps

  1. Warm hydraulic oil

    Before starting any calibration, ensure the hydraulic oil is warmed to a minimum of 49°C (120°F).

  2. Attempt EHR calibration

    Access the tractor's diagnostic menu (often the 'H' menu or remote valve settings) to perform a calibration of the electro-hydraulic remote valves. On some models, you may need a special tool (e.g., 380001903) to connect to the diagnostic port. Follow on-screen prompts. If calibration for remote #1 fails, proceed to the next step.

  3. Inspect valve spool

    Safely relieve all hydraulic pressure. Attempt to manually stroke the valve back and forth to clear any debris. If the spool is mechanically stuck, remove and disassemble the valve assembly for inspection and cleaning.

  4. Test position sensor (potentiometer)

    Locate the potentiometer on the remote valve body. Using a multimeter, check the resistance of the potentiometer as it is moved through its range. The reading should change smoothly without any dropouts or spikes.

  5. Replace faulty components

    If the potentiometer fails the resistance test, replace it. If the valve spool is damaged or cannot be freed, replace the entire valve slice or assembly.

  6. Perform final calibration

    After replacing any components of the EHR system, a full calibration of the remote valves is mandatory to ensure the controller learns the new component's position and operational range.

Parts you might need

(16)
  • Compatible with T4, T5, T6, T7, and TM series. Supersedes 82012603, 82017351, 82021036, 82033385, 87559692, 82010303.

  • Flow Control Knob Potentiometer

    87663294

    For the armrest unit on some T-series tractors.

  • Fits older models like the 8670, 8770, 8870, and 8970 series.

  • Fits many T6 and T7 series tractors, as well as Case IH Maxxum and Puma models.

  • Suitable for T6000 series and Case IH Maxxum/MXU/Puma models.

  • Complete Rear Remote Hydraulic Valve

    719936046

    Listed as a complete rear remote hydraulic valve for position #1.

  • Rear Remote Hydraulic Valve Kit

    MT20116103

    Rear remote hydraulic valve kit.

  • Remote Control Valve Section / Spool Valve

    86524700

    Exact part numbers vary heavily by tractor model and hydraulic stack configuration.

  • Remote Control Valve Section / Spool Valve

    84405721

    Exact part numbers vary heavily by tractor model and hydraulic stack configuration.

  • Fits various 10, 30, 40, 60, TM, TS series

  • Rear Remote Valve Seal Kit

    86535818

    Fits TC35

  • Rear Remote Valve Seal Kit (Aftermarket)

    QTP-43651

    Fits T6 and TSA series

  • Electronic Rear Remote Valve (individual)

    719412184

    Example for Position 5, illustrates component type

  • Diagnostic connector tool

    380000843

    Required to access diagnostic mode on some models

  • Listed for TM, T4000, and T7000 series tractors

  • Rear Remote Valve Potentiometer

    86729675

    Listed as a general New Holland potentiometer

Get help to fix this fault by requesting a quote

Browse other New Holland codes