4119

New Holland 4119 – EHR: Rear Remote No. 2 Over Voltage

Issue description

The control system has detected a voltage in the rear remote number two circuit that is above the manufacturer's specified limit. Logged by the Rear Electronic Hydraulic Remote Valves controller, this over-voltage condition indicates an electrical anomaly within the command and execution chain between the armrest controls and the remote valve, which can prevent proper operation and risk damage to hydraulic components.

Applies to these machines

  • T7.175
  • T7.185
  • T7.190
  • T7.200
  • T7.210
  • T7.220
  • T7.225
  • T7.230
  • T7.235
  • T7.245
  • T7.250
  • T7.260
  • T7.270
  • T6.120
  • T6.140
  • T6.145
  • T6.150
  • T6.155
  • T6.160
  • T6.165
  • T6.175
  • T6.180
  • T5
  • T6000
  • T7000
  • TM

Check the cause

  1. Check for other fault codes related to the charging system or power supply

  2. Verify no external power supplies (such as a booster pack) are connected to the tractor, which can cause an over-voltage condition

  3. Inspect the charging system by running the engine at a high idle (e.g., 2000 RPM) and checking battery voltage via the instrument cluster to rule out an overcharging alternator

  4. Inspect the wiring harness and connectors leading to the number 2 rear remote valve solenoid for chafing, corrosion, loose connections, or a short circuit to a power source (particularly where the harness passes under the cab)

  5. Swap the solenoid from remote #2 with a known good solenoid from another remote to determine if the fault follows the solenoid or remains in the wiring/controller

  6. Perform a signal valve pressure test on the load-sensing line to rule out hydraulic issues that might be misdiagnosed as electrical

Repair steps

  1. Rectify wiring or charging issues

    If damaged wiring, corroded connectors, or charging system faults (such as an overcharging alternator) are found, repair or replace the affected components first. Clear the fault codes and re-test the system.

  2. Replace the solenoid/coil

    If the solenoid is identified as faulty during the swap test, relieve all hydraulic pressure and disconnect the tractor's battery. Unbolt and remove the solenoid coil from the valve body, clean the mounting surface, and install the new solenoid ensuring all electrical connections are clean and secure.

  3. Replace the valve section

    If the issue is internal to the valve and not just the solenoid, replace the entire rear remote valve section (slice).

  4. Replace the control module

    If all other components test correctly and the fault persists, the EHR control module itself may be faulty. Replace the module as a last resort. Replacement of the control module may require programming by a certified dealer.

Parts you might need

(15)
  • Replaces 87723774.

  • OEM

  • Solenoid47833382

    OEM

  • General-purpose hydraulic valve solenoid coil

    QTP-44308

    Aftermarket SKU for T5, T6, and T7 series.

  • Complete electro-valve assembly (OEM).

  • Rear Remote Valve Section/Slice

    59999927

    Replaces 47887017. Single section of the remote valve stack (OEM).

  • Rear Remote Valve Kit (Single)

    MT20116103

    Complete kit for adding or replacing a single remote valve (OEM).

  • Rear Remote Valve Kit (Two-spool)

    710440016

    Complete kit for adding or replacing two-spool remote valves (OEM).

  • Rear Remote Valve

    719195010

    Alternative OEM part number for Case New Holland.

  • Aftermarket option compatible with various T6 and T7 series.

  • For T7 series

  • 2nd Rear Remote Kit

    719279022

Get help to fix this fault by requesting a quote

Browse other New Holland codes