4128

New Holland 4128 – EHR: Rear Remote No.3 No Control Message Received

Issue description

The main vehicle controller has not received a CAN bus control message from the electronic control module integrated into the third rear remote hydraulic valve. This communication failure prevents the primary control unit from confirming the status or commanding the operation of remote valve #3, which is often caused by wiring issues, low system voltage, or a failed electronic module on the valve itself.

Applies to these machines

  • T6000 Series
  • T6010
  • T6070
  • T7000 Series
  • T7050
  • T7060
  • T6 Series
  • T6.120
  • T6.175
  • T7 Series
  • T7.170
  • T7.210

Check the cause

  1. Perform a basic system reset by toggling the master switch for the remotes or restarting the tractor to clear temporary software glitches

  2. Inspect for low voltage and bad grounds; ensure the battery is fully charged and main chassis/cab ground straps are clean and tight

  3. Visually inspect the wiring harness and connector at the #3 rear remote valve for chafing, corrosion, pinching, or loose seating

  4. Swap the electronic control module from a working remote (e.g., #2 or #4) with remote #3 to see if the fault code follows the module or stays with the wiring

  5. Perform CAN bus diagnostics: check resistance between CAN High and CAN Low (should be ~60 ohms) and verify voltages (CAN High ~2.5-3.5V, CAN Low ~1.5-2.5V)

  6. Conduct a load sense line pressure test to verify the hydraulic pump receives the signal to go on and off load

Repair steps

  1. Address basic electrical issues

    Rectify any issues with low voltage, bad grounds, or damaged wiring found during inspection. Clean and secure all relevant connectors with dielectric grease.

  2. Isolate faulty component

    Based on module swapping and CAN diagnostics, determine if the failure lies in the valve's electronic module, the wiring harness, or the main controller.

  3. Replace remote valve or module

    Thoroughly clean the area, relieve hydraulic pressure, and disconnect electrical/hydraulic lines (cap them to prevent contamination). Unbolt and remove the faulty valve section, install the new component ensuring seals are seated, and reconnect lines.

  4. Test and calibrate

    Start the tractor, test the function of all remote valves, and check for leaks. Perform a calibration procedure using the New Holland electronic service tool so the system recognizes the new component.

Parts you might need

(19)
  • Fits many T6, T7, and Case IH Maxxum/Puma models

  • Rear remote valve

    719195010

    Case New Holland rear remote valve

  • Remote control valve with Mega Flow

    86026993

    Ford/New Holland specific

  • Rear remote hydraulic valve kit

    MT20116103

    Kit assembly

  • Electronic Controller for Remote Valve

    Generic part name if module is available separately

  • Rear Remote Hydraulic Control Valve (EHR Valve Slice)

    47675278

    For some compacts

  • Rear Remote Hydraulic Control Valve (EHR Valve Slice)

    86403116

    Self-centering kit

  • Remote Valve Seal Kit

    86535818

    If replacing or rebuilding the hydraulic portion of the valve

  • Remote Control Valve

    47873781

    Electro-hydraulic unit (Bosch Rexroth). Fits T-series and TM-series.

  • Electro-hydraulic unit (Bosch Rexroth). Fits T7030, T7040, T7050, and T7060 models.

  • Electro-hydraulic unit (Bosch Rexroth). Fits T-series and TM-series.

  • Armrest Controller

    87399131

    Fits T7000 series (T7030, T7040, T7050, T7060).

  • Armrest Electronic Control Unit

    48068685

    Electronic Control Unit for Armrest Control Module.

  • Remanufactured Armrest Controller

    84165726R
  • Armrest Controller

    84366982

    Fits T9 series.

  • Example part number. Verify with dealer by serial number.

  • Rear Remote Hydraulic Valve Kit

    SBA340003250

    Kit for adding remotes.

Get help to fix this fault by requesting a quote

Browse other New Holland codes