4144

New Holland 4144 – ARU: Remote Control Valve 4 EEPROM Error

Issue description

The system has detected an error related to the EEPROM of the rear remote control valve No. 4. This indicates a problem with the memory or data storage associated with this component. The configuration and calibration data is corrupt, unreadable, or has failed a checksum verification, which prevents the controller from operating the valve and typically forces it into a disabled or failsafe mode.

Applies to these machines

  • T7 Series
  • T8 Series
  • T9 Series
  • TM120
  • TM130
  • TM140
  • TM155
  • TM175
  • TM190
  • T7030
  • T7040
  • T7050
  • T7060
  • T7.230
  • T7.245
  • T7.260
  • TM135
  • Boomer
  • Compact tractor models

Check the cause

  1. Power cycle the tractor by turning it completely off, waiting a few minutes, and restarting to clear potential temporary electronic glitches

  2. Check for other active fault codes, particularly those related to the armrest controller, CAN bus communication, or power supply issues, which could be the root cause

  3. Visually inspect the wiring harness and connectors leading to the No. 4 remote valve for signs of damage, corrosion, or loose connections

  4. Attempt to recalibrate the remote valves through the tractor's instrument cluster display (often in an 'H' menu) by moving the control lever to its maximum extents to re-synchronize it with the valve and resolve loss of synchronization or data corruption

Repair steps

  1. Prepare machine for service

    Park the tractor on a level surface, lower all implements to the ground, and shut down the engine.

  2. Identify and clean valve area

    Locate the stack of rear remote valves and identify the fourth valve. Thoroughly clean the area around the valve and its hydraulic connections to prevent contamination of the hydraulic system.

  3. Remove faulty valve assembly

    Carefully disconnect the electrical connector and hydraulic lines (be prepared for residual fluid to leak). Unbolt and remove the old valve assembly.

  4. Install new valve assembly

    Install the new valve assembly, ensuring all seals and O-rings are correctly seated. Reconnect the hydraulic lines and the electrical connector.

  5. Recalibrate the new valve

    Access the calibration menu through the tractor's display and follow the on-screen prompts to calibrate the newly installed valve so the control unit can learn its parameters.

  6. Test functionality and check for leaks

    Start the tractor, check for any hydraulic leaks around the new valve, and operate the No. 4 remote valve to ensure correct functionality.

Parts you might need

(11)
  • For T7030, T7040, T7050, T7060, T7.230, T7.245, T7.260, and various TM series tractors (associated with Bosch 521 610 025)

  • Electro-Hydraulic Remote Valve Assembly

    84173993

    Supersedes 718348056, for Boomer and compact models

  • Replaces 5190712, for models like TM135

  • Electronic Rear Remote Valve

    719412184

    For position 5, indicating that different positions may have unique part numbers

  • Remote Control Valve (Mega Flow)

    86026993

    Mega flow remote control valve

  • Solenoid87638226

    Replaces 5190767, component part for some models (e.g., TM135)

  • Replaces 5190768, component part for some models (e.g., TM135)

  • Remote Control Valve

    47873781

    OEM New Holland remote control valve. Verify fitment by serial number.

  • Valve, Remote CO

    86403116

    Fits various Boomer and compact models, supersedes 86554978.

  • Remote Valve Kit

    731200551

    Fits some WORKMASTER and FARMALL models.

  • Diagnostic Connector

    380000843

    May be required to enter calibration mode on some models.

Get help to fix this fault by requesting a quote

Browse other New Holland codes