New Holland 4165 – Rear EHR: Rear Remote No. 5 Manually Operated
Issue description
The controller has detected movement in the spool of the 5th rear remote hydraulic valve without receiving an electronic command from the cab controls. This code is normally triggered when an operator uses the physical manual override lever/knob, but if logged unexpectedly, it indicates the valve spool is physically stuck, the manual override linkage is jammed, or the spool position transducer is failing.
Applies to these machines
15 machines- T7
- T6000
- T9 Series
- T6010
- T6020
- T6030
- T6040
- T6050
- T6060
- T6070
- T6080
- T7050
- T8010
- Maxxum 115
- Maxxum 125
Check the cause
Inspect the manual override lever on the #5 rear remote valve body to check if it has been physically engaged.
Check for debris or obstructions that might be holding the manual override mechanism in the engaged position.
If the manual override is not physically activated, inspect the wiring and connectors leading to the #5 remote valve for damage, corrosion, or loose connections that could create a false signal.
Confirm with the operator that they have not intentionally or accidentally engaged the manual override.
Repair steps
Disengage manual override
If the manual override lever is found to be activated, return it to its normal, non-manual position to deactivate the fault code and restore electronic control.
Cycle power
After disengaging the lever, shut down the tractor and restart it to clear the code from the system.
Address sensor or wiring faults
If the code persists after ensuring the lever is in the correct position, test the sensor for proper operation (voltage or resistance) according to the service manual. If the sensor is faulty, the remote valve section may need to be replaced.
Calibrate remote valves
If the remote valve or a related controller is replaced, perform a calibration of the electronic remote valves through the tractor's diagnostic menu to synchronize the control levers with the valve spools, which sometimes requires a special tool.
Parts you might need
(21)Fits various T-series and Maxxum models. Replace if the valve body or internal sensors are faulty.
Armrest Control Module
47443335Replace if the fault is traced back to the controller in the armrest.
Reman Armrest Controller
84165726RRemanufactured option for the armrest controller.
- Joystick Control Lever47826727
Sends signals to the module.
Joystick Control Lever
84208937Sends signals to the module.
Electronic Rear Remote Valve - Position 5
719412184Listed for New Holland Construction equipment
- Hydraulic Valve Spool82847531
Example fitment for select NH construction/ag models.
Rear Remote Valve Kit (Complete Slice)
MT20116103If the mechanical spool itself is scored and sticking, the entire valve slice may need replacement.
Rear Remote Valve Kit
710440016Two-Spool Kit. If the mechanical spool itself is scored and sticking, the entire valve slice may need replacement.
Rear Remote Valve Kit (Complete Slice)
719195010If the mechanical spool itself is scored and sticking, the entire valve slice may need replacement.
Rear Remote Valve Assembly
47675278Fits Workmaster series
Double Rear Remote Valve Assembly
47829237Fits T9 series
Part numbers can vary by specific tractor model and production date. Always verify with a parts diagram for the specific tractor's serial number.
Assy, Remote Coupler or VALVE; Remote Coupler
92152358For remote 5. Part numbers can vary by specific tractor model and production date. Always verify with a parts diagram for the specific tractor's serial number.
- CARTRIDGE; Aux Coupler84262367
For issues related to the hydraulic connection and flow.
Rexroth valve for Case New Holland
Hydraulic Valve Solenoid Coil
QTP-44308Aftermarket, fits various T5, T6, T7, TM, TSA series
- Hydraulic Valve Solenoid Coil87472229
OEM, fits various T5, T6, T7 series
- Remote Control Valve Seal Kit83926520
Fits a wide range of older New Holland series
Remote Control Valve Seal Kit
87610517Case/New Holland OEM
Get help to fix this fault by requesting a quote
