4315

New Holland 4315 – EHR: Rear Remote No.7 - No EHR Control Messages

Issue description

The tractor's CAN bus network has lost communication with the 7th rear electro-hydraulic remote (EHR) valve. The main controller is not receiving the expected electronic control messages from this specific valve slice. This typically indicates an open circuit in the CAN wiring, a disconnected plug, a failed electronic module on the valve itself, or a software configuration error.

Applies to these machines

  • T8.275
  • T8.300
  • T8.330
  • T8.360
  • T8.390
  • T8.420
  • Magnum 235
  • Magnum 340
  • T7000 Series
  • T9 Series

Check the cause

  1. Check for other simultaneous fault codes, which may indicate a broader network issue or low battery voltage

  2. Inspect battery voltage (ideally 12.6V) and ensure chassis and cab ground straps are clean and secure

  3. Perform a CAN Bus power-off test: measure resistance across CAN_H and CAN_L (should be ~60 Ohms; 120 Ohms indicates an open circuit/missing resistor, lower indicates a short)

  4. Perform a CAN Bus power-on test: measure DC voltage of CAN_H and CAN_L to ground (both should be ~2.5V when idle)

  5. Visually inspect the wiring harness and connectors between the armrest controller and the #7 rear remote valve, especially at articulation points and the plug under the right-hand cab above the battery box

  6. Isolate the component by swapping the electrical connector from remote valve #7 with an adjacent functioning remote (e.g., #6 or #8) to see if the fault code follows the valve or stays with the wiring

Repair steps

  1. Repair wiring and connectors

    If damaged wiring or corroded connectors were found during diagnosis, repair or replace them and ensure all connections are clean and secure.

  2. Replace remote valve electronic module

    If the fault is isolated to the #7 remote valve itself, disconnect the electrical connector, unbolt the electronic module (pilot head) from the valve block, install the new module ensuring seals are seated, and reconnect.

  3. Replace armrest controller

    If diagnostics point to the armrest controller, disconnect the battery, disassemble the armrest, disconnect all electrical connectors, install the new unit, and reconnect wiring.

  4. Perform system calibration

    After replacing either the remote valve module or the armrest controller, perform a calibration procedure using the tractor's instrument cluster display or an Electronic Service Tool (EST) so the system recognizes the new component.

Parts you might need

(11)
  • Rear Remote Hydraulic Valve Kit

    MT20116103

    Complete valve kit; verify fitment by serial number

  • Two-Spool Remote Valve Kit

    710440016

    Verify fitment by serial number

  • Valve Assembly (Older Case IH)

    1980311C6

    Verify fitment by serial number

  • Valve Assembly (Older Case IH Alternative)

    186760A6

    Verify fitment by serial number

  • Armrest Controller (Remanufactured)

    84165726R

    Verify fitment by serial number

  • Armrest Controller (T7000 Series)

    87399131

    Fits some T7000 series tractors

  • Armrest Controller (T9 Series)

    84366982

    Fits some T9 series tractors

  • General armrest part

  • Electro-Hydraulic Rear Remote Valve Section / EHR Valve Slice

    47675278

    Exact slice numbers for T8/T9 stacks require a serial number lookup. Requires software configuration and calibration via the CNH EST tool after physical installation.

  • Electro-Hydraulic Rear Remote Valve Section / EHR Valve Slice

    719195010

    Exact slice numbers for T8/T9 stacks require a serial number lookup. Requires software configuration and calibration via the CNH EST tool after physical installation.

  • Exact slice numbers for T8/T9 stacks require a serial number lookup. Requires software configuration and calibration via the CNH EST tool after physical installation.

Get help to fix this fault by requesting a quote

Browse other New Holland codes