4350

New Holland 4350 – Rear Electro-Hydraulic Remotes: Rear Remote 6 Spool Not Calibrated

Issue description

The No. 6 rear electro-hydraulic remote (EHR) valve spool has lost its calibration data or the calibration is out of range. The control module is unable to verify the precise position of the spool within the valve body, which prevents the system from accurately controlling hydraulic flow and may lead to improper operation or complete deactivation of the associated hydraulic function. The system requires a calibration routine to be run to relearn the spool's end-of-travel limits.

Applies to these machines

  • T7.170
  • T7.185
  • T7.200
  • T7.210
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • T8.xxx
  • T9.390
  • T9.450
  • T9.505
  • T9.560
  • T9.615
  • T9.670

Check the cause

  1. Review active and stored fault codes for other errors that could affect the hydraulic system or CAN bus communication

  2. Inspect the wiring harness and connectors associated with the number 6 remote valve for any signs of damage, corrosion, or loose connections

  3. Check the hydraulic system to ensure the oil level is correct and the oil is clean

  4. Manually cycle the valve back and forth to help clear any debris that might be obstructing the spool's movement

  5. Verify the EHR valves are correctly addressed or configured on the CAN network, if indicated by service literature

Repair steps

  1. Access diagnostics menu

    With the key in the 'ON' position, access the service or diagnostics menu (often referred to as the 'H' menu) on the tractor's display.

  2. Navigate to calibration

    Within the H menu, navigate to the section for hydraulic or remote valve calibration.

  3. Select valve

    Use the increment/decrement keys or touchscreen to select remote valve number 6.

  4. Initiate calibration

    Press the appropriate key (often labeled 'PROG' or similar) to start the calibration process for the selected valve.

  5. Follow on-screen prompts

    Move the corresponding control lever to its full 'raise' and 'lower' positions as prompted by the display. The system will record the sensor values at these endpoints.

  6. Confirm completion

    The display will indicate when the calibration has been successfully completed. If the calibration fails repeatedly, inspect the valve's internal potentiometer, solenoid, or control lever for hardware faults.

Parts you might need

(20)
  • OEM part number example for T6/T7 series

  • OEM part number example for various CNH models

  • Rear Remote Hydraulic Valve Kit

    MT20116103

    Dealer installed accessory

  • Spool Valve Control Cable

    QTP-43824

    For tractors with cable-operated controls (example for T6/T7 series)

  • Spool Valve Control Cable

    QTP-43826

    For tractors with cable-operated controls (example for T6/T7 series)

  • Special Tool380001903

    Required for some T9 series tractors to connect to the valve block to perform calibration

  • Supersedes 84385135, 87312136, 47128303, 5184312. Provides real-time position feedback to the control unit.

  • Two-Spool Remote Valve Kit

    710440016

    Example part number; actual replacement valve assembly part numbers are specific to the tractor model and configuration.

  • Single Spool Remote Kit / Remote Control Valve

    84171957

    Replaces older part 718334026

  • Single Spool Remote Kit / Remote Control Valve

    718334026

    Older part replaced by 84171957

  • Remote Control Valve Assembly

    86403116
  • Rear Remote Hydraulic Control Valve

    47675278
  • Rear Remote Valve

    719195010
  • Remote Hydraulic Control Valve Spool

    86990388

    Example from T8030, verify with serial number

  • Remote Hydraulic Control Valve Assembly

    87338964

    Example from T8030, verify with serial number

  • Example from T8030, verify with serial number

  • Example from T8030, verify with serial number

  • Verify fitment by serial number

  • Verify fitment by serial number

  • E.H.R. Control Module

    86029094

    Replaces 86026900 (for 8670A-8970A)

Get help to fix this fault by requesting a quote

Browse other New Holland codes