4501

New Holland 4501 – ACM: Remote No.1 Control Message not plausible

Issue description

The Armrest Control Module (ACM) is receiving an illogical or out-of-range signal from the No. 1 remote valve lever (paddle or joystick). The controller cannot trust the position information, which could be caused by a constant 'on' signal, no signal, or erratic voltage from the lever's internal sensor. This unreliable control message may affect the proper operation of the connected hydraulic system.

Applies to these machines

  • T7 Series
  • T7000 Series
  • TG Series
  • TM Series
  • T7030
  • T7040
  • T7050
  • T7060
  • T8 Series
  • T9 Series
  • Puma
  • MX Series

Check the cause

  1. Check for other active fault codes (e.g., under/over voltage 4104, 4105, or CAN bus errors) that might indicate a broader electrical issue rather than a single component failure

  2. Visually inspect the wiring harness that runs to the armrest controller for signs of chafing, pinching, or damage to the connectors, which can cause intermittent signals

  3. Check system voltage to ensure the battery is fully charged and the charging system is functioning correctly, as low battery voltage can cause numerous 'ghost' electronic faults

  4. Observe system behavior to note if the fault is constant or intermittent, if wiggling the lever or harness affects it, or if the remote activates on its own

Repair steps

  1. Enter Calibration Mode

    Access the tractor's service or diagnostics menu. This may require a specific key sequence or navigating through the settings on the corner post or main display (often referred to as the 'H Menu').

  2. Select Valve Calibration

    Navigate to the menu for hydraulic or remote valve calibration. On some systems, this may be labeled 'EHR CAL' or similar.

  3. Initiate Calibration for Remote #1

    The display will prompt you to move the specific remote lever (No. 1) to its full 'extend' (rearward) and 'retract' (forward) positions, holding it in each detent until the system acknowledges the position.

  4. Save and Exit

    Once the calibration sequence is complete, the system will indicate success. Turn the key off and wait for a designated period (e.g., 10-30 seconds) to ensure the new values are stored in the controller's memory.

  5. Test Operation

    Restart the tractor and test the function of remote No. 1. If the fault code is gone and the remote operates correctly, the issue is resolved.

  6. Isolate the Faulty Component

    If calibration fails or the fault immediately returns, the issue is likely a hardware failure in the remote lever assembly. The fault is with the No. 1 remote lever assembly located in the armrest.

  7. Disassemble Armrest

    Carefully disassemble the armrest console to gain access to the bank of remote levers.

  8. Replace the Lever/Joystick

    Unplug and replace the faulty No. 1 remote lever module. Depending on the tractor's configuration, this may be a simple paddle lever or a more complex multi-function joystick.

  9. Reassemble and Recalibrate

    After installing the new component, reassemble the armrest. It is critical to perform the EHR calibration procedure again with the new part to synchronize it with the tractor's control module.

Parts you might need

(12)
  • Used on SideWinder II armrest consoles for Auto Command CVT tractors. This is a complex joystick that integrates multiple functions. Supersedes part numbers 84385153, 87312154, 47128321, and 5184330.

  • Fits T7 series tractors (Tier 4A/4B) and equivalent Case IH Puma models. Manages EHR, front loader, and shuttle commands. Supersedes part numbers 84385125, 87312125, 47128292, and 5184301.

  • Complete Armrest Assembly

    87399131

    This is the entire electronic armrest assembly for models like the T7030, T7040, T7050, and T7060. An alternative part number is 87631906.

  • Armrest Control Module (ECU)

    48068685

    This is the electronic control unit that regulates the Armrest Control Module. It is less likely to be the cause of a single-lever fault than the lever itself.

  • Mid-Mount Hydraulic Control Valve Kit (2-spool)

    719349006

    Verify fitment by serial number

  • Verify fitment by serial number

  • Replaces Bosch 521 610 025. Fits various T7 and TM series tractors.

  • Remote Control Valve with Mega Flow

    86026993

    Verify fitment by serial number

  • Verify fitment by serial number

  • Joystick/Control

    87567643

    Replaces 87588931

  • Hydraulic Valve Remote Kit

    SBA340003250

    Verify fitment by serial number

  • Hydraulic Valve Remote Kit

    309973F

    Verify fitment by serial number

Get help to fix this fault by requesting a quote

Browse other New Holland codes