5001

New Holland 5001 – Rear PTO: PTO Switch Activated During Power Up

Issue description

Fault code 5001 indicates that one of the Power Take-Off (PTO) engagement switches (such as the main cab switch, Auto PTO switch, or remote fender switch) was in the 'on' or activated position at the moment the tractor was powered on. The control system flags this condition as a potential safety hazard to prevent unintended operation of the PTO. As a built-in safety feature, this fault may prevent the engine from starting or inhibit PTO engagement until the fault is cleared.

Applies to these machines

  • T-Series
  • TM115
  • TM125
  • TM135
  • TM150
  • TM165
  • 35 Series
  • 40 Series
  • 60 Series
  • TNF
  • TNS

Check the cause

  1. Verify operator procedure: Confirm that all PTO switches (main cab, Auto PTO, and external fender-mounted) are in the 'off' position before turning the tractor's key to the 'on' or 'start' position.

  2. Inspect the main cab PTO switch for physical damage, sticking, or looseness. Ensure it moves to and stays in the 'off' position with a positive detent.

  3. Check the external fender-mounted PTO switch(es) for water and dirt ingress, sticking, or damage. Ensure the protective cap is in place.

  4. If equipped, ensure the 'Auto PTO' function is disengaged and not malfunctioning.

  5. Check for a No-Start Condition: Verify if the tractor refuses to start, which is a built-in safety feature associated with this fault.

  6. Visually inspect the wiring harnesses leading to the cab, fender, and other PTO-related switches. Look for corroded connectors, chafed or broken wires, and loose connections, especially behind the dash and near the rear fender.

  7. Test battery voltage and grounding. Ensure the battery is fully charged (above 12.6V) and that main chassis ground connections are clean and tight.

Repair steps

  1. Disconnect battery

    Before beginning any electrical repairs, disconnect the tractor battery to prevent electrical shorts.

  2. Isolate the faulty switch

    Disconnect the electrical connector of the suspected switch (e.g., the fender switch). Reconnect the battery and power up the tractor. If fault code 5001 disappears, the disconnected switch or its immediate wiring is the culprit.

  3. Replace faulty PTO switch

    Access the switch by removing necessary dash panels or fender components. Unplug the wiring harness by depressing the locking tab. Remove the old switch by pinching its plastic side clips or removing the retaining nut. Push the new switch firmly into the mounting hole until it clicks into place.

  4. Repair damaged wiring

    If a wiring issue is found, cut out the damaged section and splice in a new piece of wire of the same gauge using weatherproof heat-shrink butt connectors. Clean corroded connectors with electronics cleaner or replace them.

  5. Test system

    Reconnect the electrical connector and the tractor battery. Turn the key to the 'on' position (without starting the engine) and verify that fault code 5001 does not reappear. Test the function of the new switch to ensure the PTO engages and disengages correctly.

Parts you might need

(8)
  • Fits New Holland TM Series (TM115, TM125, TM135, TM150, TM165). Replaces 82027012.

  • General external PTO switch for engaging and disengaging the system.

  • Generic PTO switch listed on the CNH parts store; verify specific model fitment.

  • PTO Switch81869844

    Fits 40 Series, 35 Series, and some Fiat tractors. Replaces 81864295, 81864300, E9NN10N927AA, F0NN10N927AA, F0NN10N927AB.

  • PTO SwitchMT40339438

    Genuine OEM part; specific model application not listed.

  • PTO Engagement Switch (Aftermarket)

    QTP-409650

    Aftermarket switch stated to fit Ford New Holland 35, 40, 60, TNF, TNS series, and Fiat M/L series.

  • Fits some Ford/New Holland models. Cross-references to part numbers 86603490 and 87300397.

  • PTO and Brake Switch

    E4NN13480AA

    Referenced for a wide range of older Ford/New Holland models.

Get help to fix this fault by requesting a quote

Browse other New Holland codes