5036

New Holland 5036 – EMU, TCM, or VCU: Rear PTO Failure To Start

Issue description

The electronic control module has detected that the rear Power Take-Off (PTO) has not engaged as commanded. This fault typically indicates a relay or switch wiring fault within the electrical control circuit. The system commanded the PTO to start but did not receive a confirmation signal, or it detected an open or short in the activation circuit.

Applies to these machines

  • T4 Series
  • T5 Series
  • T7 Series
  • T8 Series
  • TT Series
  • TM Series
  • TM120
  • TM190
  • TS Series
  • TS90
  • TS100
  • TS110
  • TB Series
  • TB80
  • TB85
  • TB90
  • TB100
  • TB110
  • TB120
  • Workmaster 50
  • 5110
  • 5610
  • 6610
  • 6710
  • 6810
  • 7710

Check the cause

  1. Check for other active or stored fault codes (e.g., 5006/5007 for the solenoid circuit, or 5034/5035 for the fender switch) to narrow down the root cause

  2. Verify basic operational conditions are met (operator in seat, tractor in correct gear or neutral, engine running at specified RPM)

  3. Inspect all fuses and relays related to the PTO circuit. Swap the PTO relay with a known good relay of the same type to test its function

  4. Test the main cab PTO engagement switch and rear fender-mounted switch (if equipped) for proper voltage, open circuits, or shorts to ground

  5. Verify the functionality of all safety interlocks, including the seat switch, clutch pedal switch, and brake switches

  6. Visually inspect the wiring harness and connectors for the PTO switch, solenoid, and sensors for corroded terminals, broken wires, or loose connections

  7. Test the PTO solenoid by listening for an audible 'click' when activated, checking for voltage at the connector, and testing the coil for continuity or resistance

  8. Check hydraulic/transmission fluid level and condition. Low fluid prevents pressure buildup, and burnt-smelling fluid indicates an overheated/failing clutch pack

Repair steps

  1. Repair wiring or connectors

    If a wiring fault is found, remove the rear PTO switch, inspect its connector and terminals, and repair or replace damaged harness sections. Clean any corroded connectors.

  2. Replace defective switches

    If the cab or fender switch is found to be defective, remove the console panel or housing and replace the switch with a new part.

  3. Replace PTO relay

    If the PTO relay is identified as the fault, replace it with a new, matching relay.

  4. Replace PTO solenoid

    If the solenoid receives power but does not actuate, relieve hydraulic pressure, unscrew the solenoid coil from the rear hydraulic valve block, and install a new solenoid with correct seals/O-rings torqued to specification.

  5. Replace PTO clutch pack

    If electrical and hydraulic control issues are definitively ruled out and symptoms like slipping under load or burnt fluid persist, split the tractor and replace the PTO clutch pack (best left to a qualified technician).

  6. Perform calibration

    After replacing transmission or PTO components, perform a calibration routine using the tractor's onboard diagnostic 'H' routines or a specialized service tool.

Parts you might need

(23)
  • PTO Clutch Pack / Assembly

    E0NNN751BA

    Also replaces 81871420, 83999544, E0NNN751BB, E9NNN707AA. Fits models like 5110, 5610, TS90, TB100.

  • PTO Solenoid / PTO Solenoid Coil

    Highly model-specific; located on the rear hydraulic valve block.

  • PTO Switch / Rocker Switch

    Cab switch; highly model-specific.

  • Fender Mounted PTO Switch

    Highly model-specific; associated with fault codes 5034 and 5035.

  • Control Valve O-Ring

    238-5036

    Common New Holland O-ring replacement

  • PTO Clutch Kit

    534934R92
  • PTO Clutch Disc Kit

    68802C91
  • PTO Clutch Disc Kit

    68803C91
  • PTO Clutch Plate

    E1657
  • PTO Clutch Plate

    E1658
  • PTO Clutch Plate

    L33125
  • PTO Clutch Plate

    L33563
  • Transmission & PTO Clutch Disc

    RE17420
  • PTO Switch82028271

    Fits various T4, T5, T6, T7, TM, and TS series tractors

  • PTO SwitchMT40339438

    Fits some New Holland models

  • Solenoid Valve

  • PTO Solenoid Control Valve Cylinder

    51433464

    Fits models like the TD5 series

  • Green Connector Solenoid

    QTP-43604

    Specific type of solenoid for PTO and transmission control on New Holland T6/T7 series. Connector color is critical.

  • Clutch Assembly for various compact tractors

  • PTO Clutch

    47446961
  • PTO Clutch87731123
  • Also crosses to E0NNN751BA. Fits models including TB100, TB110, TB120, TS90, and others.

Get help to fix this fault by requesting a quote

Browse other New Holland codes