5044

New Holland 5044 – XCM: Rear PTO Speed Sensor Shorted to Ground

Issue description

The XCM (Multi-Function Controller) has detected a short circuit to ground in the electrical circuit of the rear PTO speed sensor. This magnetic inductive sensor monitors the rotational speed of the PTO output shaft. A short to ground indicates the signal wire is making unintended contact with the chassis or another ground path, sending an incorrect low or zero voltage signal. This condition can cause improper operation, failure of the PTO to engage, or unexpected disengagement.

Applies to these machines

  • T5.90S
  • T5.100
  • T5.110
  • T5.120
  • T5.130
  • T5.140
  • T6.120
  • T6.125
  • T6.140
  • T6.145
  • T6.155
  • T6.160
  • T6.165
  • T6.175
  • T6.180
  • T7.165
  • T7.170
  • T7.175
  • T7.185
  • T7.190
  • T7.200
  • T7.210
  • T7.220
  • T7.225
  • T7.230
  • T7.245
  • T7.250
  • T7.260
  • T7.270
  • T7.315
  • T6020
  • T6030
  • T6050
  • T6070
  • T6080
  • T6090
  • T7030
  • T7040
  • T7050
  • T7060
  • T7070

Check the cause

  1. Visually inspect the wiring harness leading to the rear PTO speed sensor for any signs of damage, such as chafing, cuts, or heat exposure.

  2. Disconnect the sensor's electrical connector and inspect the pins for corrosion, moisture ingress, or damage. Clean the connector thoroughly.

  3. With the sensor disconnected, use a multimeter to check for a short to ground on the signal wire in the tractor's wiring harness. There should be no continuity between the signal wire and the tractor chassis.

  4. Perform a basic sensor test: With the PTO disengaged, turn the tractor on. If the PTO attempts to turn a couple of times and then stops, the issue is likely within the speed sensor system. If it doesn't turn at all, the problem may lie with the engagement solenoid or its control circuit.

  5. Review other active fault codes to ensure electrical issues, such as low system voltage, aren't triggering multiple 'ghost' codes.

Repair steps

  1. Safety First

    Ensure the tractor is parked on a level surface, the engine is off, the parking brake is engaged, and the key is removed.

  2. Locate the Sensor

    The rear PTO speed sensor is typically mounted on the rear transmission or axle housing, directly over the internal PTO drive gear or on the PTO output shaft bearing support. On some models, you may need to remove other components, like a hydraulic filter, to gain access.

  3. Clean the Area

    Thoroughly clean the area around the sensor to prevent dirt and debris from entering the transmission housing upon removal.

  4. Remove the Old Sensor

    Disconnect the electrical connector. Unbolt the sensor from the housing. It may be held by one or two bolts. The sensor can be tight, so gentle persuasion may be necessary.

  5. Install the New Sensor

    Install the new sensor and tighten the mounting bolts to the manufacturer's specified torque.

  6. Set the Air Gap

    Pay close attention to the air gap between the sensor tip and the tone wheel (the gear it reads from). An incorrect gap—either too close or too far—can cause erratic readings.

  7. Reconnect and Secure

    Connect the new sensor's electrical plug, ensuring it is clean and seats firmly. Secure the wiring harness away from moving parts and heat sources.

  8. Clear Fault Codes

    After installation, use the tractor's diagnostic menu or a service tool to clear the stored 5044 fault code.

  9. Test Operation

    Start the tractor and engage the PTO at various speeds to verify that the dashboard display is providing a correct RPM reading and that the fault code does not return.

Parts you might need

(11)
  • Rear PTO Speed Sensor

    82022718
  • Rear PTO Speed Sensor

    82030541
  • This may be for the output shaft specifically, verify fitment

  • Listed for New Holland Construction equipment. OEM: CNH Industrial.

  • Fits New Holland TG series tractors. OEM: CNH Industrial.

  • Fits New Holland CNH models. OEM: CNH Industrial.

  • Fits T4, T3F, TD, Workmaster, Farmall C and A series. Alternate part numbers: 84390014, 84597886. OEM: CNH Industrial.

  • Rear PTO Speed Sensor

    QTP-44504

    Aftermarket alternative. Fits T5, T6, T6000, T7, Maxxum, and Puma.

Get help to fix this fault by requesting a quote

Browse other New Holland codes