5811

New Holland 5811 – UCM: Loader Lockout Switch Implausible State

Issue description

The Universal Control Module (UCM) has detected a logical inconsistency in the signal from the loader port lock switch. The switch is reporting a state that is not logically possible under normal operating conditions, such as signaling both on and off simultaneously or conflicting with other machine systems. This condition triggers an amber warning light and indicates a potential issue with the switch or its associated circuit.

Applies to these machines

  • L140
  • L150
  • L160
  • L170
  • L180
  • L185
  • L190
  • L215
  • L218
  • L220
  • L330
  • LS140
  • LS150
  • LS160
  • LS170
  • LS180
  • LS180.B
  • LS185.B
  • LS190
  • LS190.B
  • LX465
  • LX485
  • LX565
  • LX665
  • LX865
  • LX885
  • LX985
  • C185
  • C190
  • C327
  • C338

Check the cause

  1. Verify Interlock System Function: Ensure all conditions are met for normal operation (operator in the seat, seat belt fastened, and the run/service switch is in the 'RUN' position). A fault in any of these systems can prevent the lockout solenoids from receiving power.

  2. Check for Voltage at Lockout Solenoids: With the machine on and all interlock conditions met, check for 12V power at the boom and bucket lockout solenoids on the main hydraulic control valve block.

  3. Inspect Wiring and Connectors: Visually inspect the wiring harness leading to the loader lockout switch on the control console and the lockout solenoids on the hydraulic valve for loose connections, corrosion, or damaged/frayed wires.

  4. Test the Loader Lockout Switch: Test the rocker switch on the operator's console for continuity with a multimeter to check that it correctly opens and closes the circuits for the 'LOCKED' and 'UNLOCKED' positions.

Repair steps

  1. Park Safely

    Park the machine on a level surface, lower the loader arms completely, and stop the engine.

  2. Gain Access

    Depending on the model, raise the cab or remove access panels to reach the hydraulic control valve and lockout solenoids. The lockout switch is located on the operator's console.

  3. Identify and Inspect Components

    Locate the loader lockout switch, the boom and bucket lockout solenoids on the control valve, and the related wiring.

  4. Perform Diagnostic Checks

    Follow the diagnostic steps to isolate the faulty component. If wiring is found to be damaged, repair or replace the affected section of the harness.

  5. Replace the Faulty Component

    If the loader lockout switch is faulty, disconnect its electrical connector, remove it from the console, and install the new switch. If a lockout solenoid is faulty, carefully disconnect its wiring, unscrew the solenoid from the hydraulic valve block (expecting a small amount of fluid to leak), install the new solenoid, torque it to the manufacturer's specification, and reconnect the wiring.

  6. Reassemble and Test

    Reinstall any access panels that were removed and lower the cab if it was raised. Start the machine and test the function of the loader arm and bucket, as well as the lockout switch, to confirm the repair. Clear the fault code from the system.

Parts you might need

(14)
  • OEM New Holland part for L220 models

  • OEM New Holland part, fits various models including C327, C338, L330

  • Spool Lock Out Solenoid Valve

    87445987

    Fits L180, L185, L190, LS180.B, LS185.B, LS190.B

  • Spool Lock Out Solenoid Valve

    84128132

    Fits C185, L180, L190, C190

  • Spool Lock Out Solenoid Valve

    87445988

    Fits C185, L180, L190, C190

  • Spool Lock Out Solenoid Valve

    84151310

    Fits a wide range of L, LS, and LX models including L160, L170, LS160, LS170, LX865

  • Spool Lock Out Solenoid Valve

    86575596

    Fits a wide range of L, LS, and LX models including L160, L170, LS160, LS170, LX865

  • Spool Lock Out Solenoid Valve

    87030707

    Fits a wide range of L, LS, and LX models including L160, L170, LS160, LS170, LX865

  • Loader Lock Rocker Switch

    47883648

    Replaces older part number 84296544. Fits most 200 series loaders (L220, C232, etc.).

  • Proportional Loader Lock Switch (Optional)

    84537211

    Rocker switch, proportional hydraulic without detent.

  • Loader Port Lock Switch (OEM)

    9847458

    Fits a wide range of L-series and C-series loaders.

  • Loader Port Lock Switch (Aftermarket)

    LPS9847458

    Aftermarket replacement for OEM part number 9847458. Fits a wide range of L-series and C-series loaders.

  • General Switch

    87572861

    Used on L180, C175, C185. Note: May function as a lights switch, verify before use.

Get help to fix this fault by requesting a quote

Browse other New Holland codes