6021

New Holland 6021 – TCM: FWD Solenoid Stuck On

Issue description

The Transmission Control Module (TCM) has detected that the Front-Wheel Drive (FWD) solenoid is remaining in the activated (on) state when it should be off. This causes the FWD system to be unintentionally engaged, which can lead to handling issues, excessive tire wear, and driveline stress on hard surfaces. The issue may stem from a mechanical failure within the solenoid valve itself or an electrical fault keeping the circuit energized.

Applies to these machines

  • T4
  • T5
  • T7
  • T8
  • TB
  • TS
  • 40 series
  • 60 series
  • 70 series
  • 5110
  • 5610
  • 6610
  • 7610
  • 7710
  • 7740
  • 7840
  • 8240
  • 8340
  • TS90
  • TS100
  • TS110
  • TS6000

Check the cause

  1. Check battery voltage (must be above 12.5V) and ensure primary power/ground connections are clean and tight to rule out false 'ghost' codes.

  2. Visually inspect the wiring harness and connector leading to the FWD solenoid for chafing, melting, or corrosion.

  3. Perform a basic electrical test with the key on (engine off) by listening for an audible click from the solenoid when toggling the FWD switch.

  4. Perform a direct voltage test by disconnecting the solenoid and applying 12V directly to its terminals to see if it actuates (clicks).

  5. Test solenoid coil resistance with a multimeter (infinite resistance indicates an open circuit, near zero indicates a short).

Repair steps

  1. Prepare machine

    Park the tractor on a level surface, turn the engine off, remove the key, engage the parking brake, and block the wheels.

  2. Locate and clean solenoid area

    Locate the FWD solenoid on the front axle transfer box or transmission/MFWD valve block. Thoroughly clean the surrounding area to prevent dirt from entering the hydraulic system.

  3. Disconnect and prepare for spillage

    Carefully detach the wiring harness connector from the solenoid. Place a drain pan underneath to catch any hydraulic fluid that may leak.

  4. Remove faulty solenoid

    Using an appropriate wrench, unscrew and remove the solenoid from the valve body.

  5. Install new solenoid

    Ensure the new solenoid's O-rings or seals are clean and lightly lubricated with new hydraulic fluid. Screw it into the valve body and tighten to the manufacturer's specified torque. Do not overtighten.

  6. Reconnect and test

    Reconnect the electrical connector. Start the tractor, check for hydraulic leaks, operate the FWD switch to verify function, and clear the fault code from the TCM.

Parts you might need

(9)
  • New Holland OEM. Cross-references: Case/IH 100739A1 / 139307A1, Ford CAR127831, Carraro 127831.

  • Fits New Holland T4 series, TNF series, 35 series

  • FWD Solenoid Valve

    F0NN4N248AB

    Fits Ford/New Holland 6640, 7740, 7840, 8340

  • FWD Dump Valve Solenoid Assembly

    81876912-TS

    Fits TS and 40 series

  • Fits New Holland 8000 series, e.g., 8870, 8970

  • Aftermarket equivalent coil replacement

    Delta PDL12 / 38400015

    often used when the OEM only sells the entire $500+ valve assembly, but only the coil has failed

  • O-Ring Seal

    238-6021

    Replaced by 9824050. This is a common CNH transmission/hydraulic O-ring whose part number coincidentally matches the fault code; you may need this if resealing the valve block

  • Used on select Case and New Holland models

  • Older Ford/New Holland part number

Get help to fix this fault by requesting a quote

Browse other New Holland codes