87

New Holland 87 – TMF: Ground Speed Signal Failure

Issue description

The Tractor Management Function (TMF) controller has detected a failure in the ground speed signal originating from the instrumentation controller. This indicates a problem with the signal being received or processed by the system, which prevents the tractor's systems from accurately determining its travel speed over the ground. The root cause is typically a faulty ground speed sensor, damaged wiring harness, or a communication issue between the sensor and the controller.

Applies to these machines

  • TM120
  • TM130
  • TM140
  • TM155
  • TM175
  • TM190
  • TS100A
  • TS110A
  • TS115A
  • TS125A
  • TS135A
  • T6010
  • T6090
  • T7030
  • T7070
  • T7.170
  • T7.270
  • TG210
  • TG255
  • TG305
  • 8670
  • 8770
  • G170
  • G190
  • G210
  • G240
  • T8
  • T9
  • TR Combines

Check the cause

  1. Visually inspect the ground speed sensor and its wiring harness for visible damage such as cracks on the sensor body, frayed or melted wires, and corrosion in the connectors.

  2. Scan for any other active error codes that could be related to the issue, such as power supply or communication faults.

  3. Perform a harness integrity check for an open circuit: With the keystart OFF, disconnect the central controller (XCM) connector C534 and the ground speed sensor connector (C237). Measure resistance between the corresponding pins; infinite resistance (OL) indicates an open circuit.

  4. Perform a harness integrity check for a short: With the sensor disconnected and keystart ON, probe the signal wire pin for voltage (indicates short to power). Turn key OFF and measure resistance between the signal wire and chassis ground; less than 10 Ohms indicates a short to ground.

  5. Verify sensor power and ground: With the sensor disconnected and key ON, verify the correct reference voltage (typically 5V, 8V, or 12V) is present at the power supply pin and that the ground pin has good continuity to the chassis.

  6. Test the sensor function: For a magnetic pickup sensor, measure resistance across its terminals and compare to OEM specs (OL indicates a faulty sensor). For a Hall Effect sensor, back-probe the signal wire while powered and slowly turn the corresponding gear/wheel to verify the voltage pulses between high and low states.

Repair steps

  1. Locate the sensor

    Find the ground speed sensor, which is typically mounted on the transmission or gearbox housing. On some models like the TS-A series, access may require the removal of components such as a hydraulic filter.

  2. Perform Diagnostic Checks

    Follow the diagnostic steps outlined above to determine if the fault lies with the sensor, wiring, or controller.

  3. Address wiring faults

    If an open circuit, short, or connector corrosion is found, repair or replace the faulty section of the wiring harness. Ensure all connections are clean and secure.

  4. Replace the sensor

    If the sensor is determined to be faulty, remove the retaining bolt and pull the sensor from its housing. It is critical to replace any O-rings or seals to prevent oil leaks upon reinstallation.

  5. Clear fault codes

    After the repair is complete, reconnect all components, clear the stored error codes from the TMF controller using the tractor's diagnostic menu or a service tool.

  6. Verify operation

    Start the tractor and operate it to ensure the fault code does not reappear and that the ground speed is reading correctly on the instrument cluster.

Parts you might need

(4)
  • Replaces 86027316, 86502050. Widely used on TM, TS-A, T6000, T7000, T7, and TG series tractors, as well as Fiat G-Series and New Holland 70 Series.

  • Replaces 1983294C1. Used on a wide variety of models including T8 and T9 tractors.

  • Sensor, True Ground Speed

    228760A1

    Listed specifically for New Holland TG255.

  • Listed for various Case IH and New Holland models.

Get help to fix this fault by requesting a quote

Browse other New Holland codes