9013

New Holland 9013 – ARM: Loss of Throttle Calibrations Memory Error

Issue description

The system has detected a controller memory error, specifically the loss of throttle calibrations. The non-volatile memory within the Armrest (ARM) controller has become corrupted or erased, losing the learned minimum and maximum positions for the hand throttle. Without this data, the engine control module (ECM) cannot accurately interpret the operator's throttle commands, which negatively affects throttle response and overall engine control.

Applies to these machines

  • T7.170
  • T7.185
  • T7.200
  • T7.210
  • T7.220
  • T7.235
  • T7.250
  • T7.260
  • T7.270
  • T7030
  • T7040
  • T7050
  • T7060
  • TG245
  • TG255
  • T4
  • T5
  • T8

Check the cause

  1. Check for other ARM controller fault codes (e.g., 9031, 1109, 3124-3128, 8011, 10091, 12013) which can provide critical diagnostic clues regarding potentiometers, voltage, or CAN bus issues

  2. Verify battery and electrical system health. Ensure the battery is fully charged (above 12.5V) and that all main power and ground connections to the cab and controllers are clean, tight, and free of corrosion

  3. Inspect the wiring harness running to the armrest controller, particularly near the main connector plug, for internal wire breaks or damage

Repair steps

  1. Enter diagnostic menu

    Access the diagnostic 'H' routines via the instrument cluster. For many T7 models, this involves holding the upshift and downshift buttons while starting the engine.

  2. Navigate to calibration menu

    Use the menu navigation buttons to find the specific calibration routine for the armrest controller or throttle (distinct from transmission or EDC hitch calibrations).

  3. Perform throttle calibration

    Follow the on-screen prompts on the instrument cluster. Move the hand throttle lever to its minimum (idle) and maximum positions to allow the controller to learn and save the new values.

  4. Save and exit

    After the sequence is complete, turn the key off and wait for at least 10-15 seconds to ensure the new calibration values are stored in the controller's memory before restarting the tractor.

  5. Address calibration failure

    If the calibration fails and code 9031 appears, this points to a hardware issue with the hand throttle potentiometer or the controller itself.

  6. Replace armrest controller

    If re-calibration is unsuccessful and other diagnostic checks do not reveal a wiring or power supply issue, replace the Armrest Controller (ARM) module or assembly. A new calibration procedure must be performed after replacement.

Parts you might need

(9)
  • Remanufactured Armrest Controller

    84165726R

    Verify fitment with a dealer using the machine's serial number.

  • Electronic Armrest Assembly with EDC Control

    87399131

    Alternative part number: 87631906. Listed for New Holland T7000 series tractors (T7030, T7040, T7050, T7060).

  • Electronic Control Unit for Armrest Control Module (ACM)

    48068685

    ECU that regulates the Armrest Control Module (ACM).

  • Verify fitment with a dealer using the machine's serial number.

  • Armrest Controller / Joystick Controller

    51575646

    New Genuine OEM. Fits various Case IH and New Holland tractors. Must be programmed with CNH EST software upon installation.

  • Armrest Controller / Joystick Controller

    399285A1

    Older TG/MX series Armrest Controller. Fits various Case IH and New Holland tractors. Must be programmed with CNH EST software upon installation.

  • T6000 series

  • Hand Throttle Potentiometer

    706067A1
  • Diagnostic test switch

    4FT 950

    Required if using the diagnostic 'H' menu (alternative: TEXA CNH Diagnosis Button Cable).

Get help to fix this fault by requesting a quote

Browse other New Holland codes