9401

New Holland 9401 – IC / UCM: Memory Error - Double Redundant Memory - Corruption Detected And Repaired

Issue description

The Instrument Cluster (IC) internal self-diagnostics have detected a corruption or inconsistency in its memory data and initiated a repair process. While the system successfully repaired the corrupted data to resolve the immediate issue, this code indicates an underlying instability in the internal memory of the controller, which may affect the proper functioning of the machine.

Applies to these machines

  • L160
  • L170
  • L180
  • L185
  • L190
  • L213
  • L216
  • L218
  • L220
  • L221
  • L223
  • L225
  • L228
  • L230
  • LS140
  • LS150
  • LS160
  • LS170
  • LS180B
  • LS185B
  • LS190B
  • C175
  • C185
  • C190
  • C227
  • C232
  • C238
  • LT185B
  • LT190B

Check the cause

  1. Record and clear the fault code using the diagnostic menu or Electronic Service Tool (EST)

  2. Monitor the machine during operation to see if the fault recurs

  3. Check battery voltage and ensure electrical connections are clean and tight to rule out 'ghost' faults

  4. Inspect electrical connectors at the Instrument Cluster (IC) and Universal Control Module (UCM) for corrosion, moisture, or damage

Repair steps

  1. Clear and monitor fault

    Note the fault code, clear it using the diagnostic menu or EST, and operate the machine. Since the memory corruption was detected and repaired, the code is often informational.

  2. Check electrical system

    Ensure the battery is fully charged and ground connections are clean and tight. Low voltage or poor grounds can cause intermittent electronic faults.

  3. Inspect module connectors

    Check the electrical connectors at the IC and/or UCM for corrosion, moisture, or damage. Clean the connectors to resolve potential intermittent issues.

  4. Replace or remanufacture control module

    If the fault code becomes persistent and recurs frequently, it indicates an impending hardware failure within the control module's memory. Replace the affected IC or UCM, or utilize a third-party remanufacturing service.

Parts you might need

(16)
  • Instrument Cluster (IC)

    87029539

    Fits various L, LS, and C series (e.g., L160, LS170, C185). Verify with serial number.

  • Fits various L, LS, and C series. Verify with serial number.

  • Instrument Cluster (IC)

    87459690

    Fits various L, LS, and C series. Verify with serial number.

  • Instrument Cluster (IC)

    84384716

    Fits various L, LS, and C series. Verify with serial number.

  • Instrument Cluster (IC)

    91790110

    Specified for the L228 Skid Steer Loader. Verify with serial number.

  • Universal Control Module (UCM)

    84529539

    For E-H Controls. Fits models like C227, C232, L218, L220. Verify with serial number.

  • For E-H Controls. Fits models like C227, C232, L218, L220. Verify with serial number.

  • For New Holland T6/T7 Tractors

  • Analog Instrument Cluster

    87668323

    Analog cluster for New Holland T6/T7 Tractors

  • Instrument Cluster

    84289366

    For T6/T7 Tractors. Supersedes to 47365942, 84408834, 84571353

  • Instrument Cluster

    91789483

    For New Holland Compact Track Loaders

  • Instrument Cluster / Electronic Instrument Cluster (EIC) Board

    86550683

    Common EIC board for older SSL models (newer models require PIN-specific lookups). Will likely need to be programmed using the New Holland EST to configure machine options and synchronize the hour meter.

  • Fits some TN-A, TD, and TD5000 series. Verify fitment by serial number.

  • Instrument Cluster

    5192091

    Fits unspecified New Holland Agriculture models. Verify fitment by serial number.

  • Instrument Cluster

    SBA385041103

    Fits T1510, T1520, T1530, TC30. Verify fitment by serial number.

  • Instrument Cluster

    EHPN10849A

    Fits older Ford/New Holland 2000-7000 series. Verify fitment by serial number.

Get help to fix this fault by requesting a quote

Browse other New Holland codes